JBXFD1G05MCSDSMR Datasheet, PDF (24/44 Pages) List of Unclassifed Manufacturers – Sealed and Unsealed Push-Pull Connectors

JBX Series
Push-Pull Connectors
Plug assembly instructions
Figure 4.A
Locator for pin and socket 0.7 - 0.9 mm and 1.3 mm contacts
Shell
size
0
1
2
3
Ø Contact
0.7
0.9
0.7
0.9
1.3
0.7
0.9
1.3
0.7
0.9
1.3
AWG
Male contact
SOURIAU P/N DANIELS P/N
22 - 24 - 26 JBX 0 OUT LP07 86 - 223
20 - 22 - 24 JBX 0 OUT LP09 86 - 225
22 - 24 - 26 JBX 1 OUT LP07 86 - 196
20 - 22 - 24 JBX 1 OUT LP09 86 - 198
18 - 20 - 22 JBX 1 OUT LP13 86 - 200
22 - 24 - 26 JBX 2 OUT LP07 86 - 202
20 - 22 - 24 JBX 2 OUT LP09 86 - 204
18 - 20 - 22 JBX 2 OUT LP13 86 - 206
22 - 24 - 26 JBX 3 OUT LP07 86 - 217
20 - 22 - 24 JBX 3 OUT LP09 86 - 218
18 - 20 - 22 JBX 3 OUT LP 13 86 - 219
ASTRO P/N
/
/
642 - 001
642 - 002
642 - 003
642 - 007
642 - 008
642 - 009
642 - 014
642 - 015
642 - 016
Female contact
SOURIAU P/N DANIELS P/N
JBX 0 OUT LP07
JBX 0 OUT LP09
JBX 1 OUT LP07
JBX 1 OUT LP09
JBX 1 OUT LP13
JBX 2 OUT LP07
JBX 2 OUT LP09
JBX 2 OUT LP13
JBX 3 OUT LP07
JBX 3 OUT LP09
JBX 3 OUT LP 13
86 - 224
86 - 226
86 -197
86 - 199
86 - 201
86 - 203
86 - 205
86 - 207
86 - 214
86 - 215
86 - 216
ASTRO P/N
/
/
642 - 004
642 - 005
642 - 006
642 - 010
642 - 011
642 - 012
642 - 017
642 -018
642 - 019
Turret with locator for pin and socket 1.6 mm and 2 mm contacts
Shell size
Ø Contact
1.6
2
2
1.6
3
2
Crimping tool 1.6
Specifications MIL-C-22520 / 7.01
AWG
14 - 16 - 18
12 - 14 -16
14 -16 - 18
12 - 14 - 16
Contacts 0.7 mm - 0.9 mm
and 1.3 mm
Specifications MIL-C-22520 / 7.01
Contacts 1.6 mm and 2 mm
SOURIAU P/N
Male & female contacts
DANIELS P/N
JBX 2 OUT LT16
TH 564
JBX 2 OUT LT20
TH 565
JBX 3 OUT LT16
TH 566
JBX 3 OUT LT20
TH 567
ASTRO P/N
650 - 030
650 - 031
650 - 038
650 - 035
MIL P/N - SOURIAU P/N
MIL-22520/7-01
MIL P/N SOURIAU P/N
MIL-22520/1-01
Supplier P/N
DANIELS: MH860
Supplier P/N
DANIELS: AF8
Buchanan: 615708
b. If using soldered contacts, prep each wire with flux and then tin dip each exposed wire end. Next pre-load a piece
of heat shrink1.6 onto the wire (Individual heat shrink tubes are optional). Solder each wire to the solder cup end
of the contact. To avoid shorts, make sure that no solder comes in contact with any other contact or wire on the connector.
24