HCPL-3180-500E Datasheet, PDF (7/16 Pages) AVAGO TECHNOLOGIES LIMITED – 2.5 Amp Output Current, High Speed, Gate Drive Optocoupler

Switching Specifications (AC)
Over recommended operating conditions unless otherwise specified.

Test
Parameter
Symbol Min.
Typ.
Max. Units Conditions
Fig.
Note
Propagation Delay Time to t_PLH
50
150 200 ns
High Output Level
Propagation Delay Time to t_PHL
50
150 200 ns
Low Output Level
I_{F =} 10 mA,
R_g = 10 Ω,
f = 250 kHz,
10, 11, 14
12, 13,
14, 23
Pulse Width Distortion
PWD
20
65
ns
Duty Cycle = 50%,
10
Propagation Delay
PDD
-90
90
ns
C_g = 10 nF
34, 35 10
Difference Between Any
(t_PHL-t_PLH)
Two Parts or Channels
Rise Time
t_r
25
ns
CL = 1 nF,
23
Fall Time
t_f
25
ns
R_g = 0 Ω
UVLO turn On Delay
t_{UVLO ON}
2.0
µs
22
UVLO turn Off Delay
t_{UVLO OFF}
0.3
µs
22
Output High Level Common |CM_H| 10
kV/µs T_A = 25°C,
24
Mode Transient Immunity
I_F = 10 to 16 mA,
11, 12
Output Low Level Common |CM_L|
10
kV/µs V_CM = 1.5 kV,
24
Mode Transient Immunity
V_CC = 20 V
11, 13
Package Characteristics

Test
Parameter
Symbol Min.
Typ.
Max. Units Conditions
Fig.
Note
Input-Output Momentary
V_ISO
3750
Vrms
T_A = 25°C,
8,9
Withstand Voltage
RH < 50%
Input-Output Resistance
R_I-O
10^[11]
Ω
V_I-O = 500 V
9
Input-Output Capacitance
C_I-O
1
pF
Freq = 1 MHz
Notes:
1. Derate linearly above +70°C free air temperature at a rate of 0.3 mA/°C.
2. Maximum pulse width = 10 µs, maximum duty cycle = 0.2%. This value is intended to allow for component tolerances for designs with IO peak
minimum = 2.0 A. See Application section for additional details on limiting IOL peak.
3. Derate linearly above +70°C, free air temperature at the rate of 4.8 mW/°C.
4. Derate linearly above +70°C, free air temperature at the rate of 5.4 mW/°C. The maximum LED junction temperature should not exceed
+125°C.
5. Maximum pulse width = 50 µs, maximum duty cycle = 0.5%.
6. In this test, V_OH is measured with a dc load current. When driving capacitive load V_OH will approach V_CC as I_OH approaches zero amps.
7. Maximum pulse width = 1 ms, maximum duty cycle = 20%.
8. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 4500 V_rms for 1 second (leakage detec-
tion current limit I_I-O < 5 µA).
9. Device considered a two-terminal device: pins on input side shorted together and pins on output side shorted together.
10. PWD is defined as |t_PHL - t_PLH| for any given device.
11. Pin 1 and 4 need to be connected to LED common.
12. Common mode transient immunity in the high state is the maximum tolerable dV_CM/dt of the common mode pulse V_CM to assure that the
output will remain in the high state (i.e. V_O > 10.0 V).
13. Common mode transient immunity in a low state is the maximum tolerable dV_CM/dt of the common mode pulse, V_CM, to assure that the out-
put will remain in a low state (i.e. V_O < 1.0 V).
14. t_PHL propagation delay is measured from the 50% level on the falling edge of the input pulse to the 50% level of the falling edge of the V_O
signal. t_PLH propagation delay is measured from the 50% level on the rising edge of the input pulse to the 50% level of the rising edge of the
V_O signal.
15. The difference between t_PHL and t_PLH between any two HCPL-3180 parts under same test conditions.
7