HCPL-0720-500E Datasheet, PDF (6/18 Pages) AVAGO TECHNOLOGIES LIMITED – 40 ns Propagation Delay, CMOS Optocoupler

IEC/EN/DIN EN 60747-5-5 Insulation Characteristics* (Option 060)

        
Description
Symbol
Installation classification per DIN VDE 0110, Table 1
  for rated mains voltage ≤ 150 V_rms
  for rated mains voltage ≤ 300 V_rms
  for rated mains voltage ≤ 600 V_rms
Climatic Classification
Pollution Degree (DIN VDE 0110/39)
Maximum Working Insulation Voltage
Input-to-Output Test Voltage, Method b*
  V_IORM x 1.875 = V_PR, 100% Production Test with t_m = 1 sec,
  Partial Discharge < 5 pC
V_IORM
V_PR
Input-to-Output Test Voltage, Method a*
V_PR
  V_IORM x 1.6 = V_PR, Type and Sample Test, t_m = 10 sec,
  Partial Discharge < 5 pC
Highest Allowable Overvoltage
(Transient Overvoltage, t_ini = 60 sec)
Safety Limiting Values –
  maximum values allowed in the event of a failure
  Case Temperature
  Input Current
  Output Power
Insulation Resistance at T_S, V₁₀ = 500 V
V_IOTM
T_S
I_S,INPUT
P_S,OUTPUT
R_IO
Characteristic
HCPL-7720
HCPL-0720
HCPL-7721
HCPL-0721
Unit
I-IV
I-IV
I-IV
55/85/21
2
630
1181
I-IV
I-III
I-III
55/85/21
2
567
1063
V_peak
V_peak
1008
907
V_peak
8000
6000
V_peak
175
230
600
≥10⁹
150
°C
150
mA
600
mW
≥10⁹
Ω
* Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under Product Safety Regulations section, (IEC/
EN/DIN EN 60747-5-5) for a detailed description of Method a and Method b partial discharge test profiles.
Note:
These optocouplers are suitable for “safe electrical isolation” only within the safety limit data. Maintenance of the safety data shall be ensured
by means of protective circuits.
The surface mount classification is Class A in accordance with CECC 00802.
Absolute Maximum Ratings
Parameter
Symbol
Min.
Max.
Units
Storage Temperature
Ambient Operating Temperature^[1]
Supply Voltages
Input Voltage
Output Voltage
Average Output Current
Lead Solder Temperature
T_S
–55
125
°C
T_A
–40
+85
°C
V_DD1, V_DD2
0
6.0
Volts
V_I
–0.5
V_DD1 +0.5
Volts
V_O
–0.5
V_DD2 +0.5
Volts
I_O 10
mA
260°C for 10 sec., 1.6 mm below seating plane
Solder Reflow Temperature Profile   
See Solder Reflow Temperature Profile Section
Figure
Recommended Operating Conditions
Parameter
Ambient Operating Temperature
Supply Voltages
Logic High Input Voltage
Logic Low Input Voltage
Input Signal Rise and Fall Times
Symbol
Min.
Max.
T_A
–40
+85
V_DD1, V_DD2
4.5
5.5
V_IH
2.0
V_DD1
V_IL
0.0
0.8
t_r, t_f 1.0
Units
Figure
°C
V
V
1, 2
V
ms
6