|
AK4543 Datasheet, PDF (11/31 Pages) Asahi Kasei Microsystems – AC’97 Rev 2.1 Multimedia Audio CODEC | |||
|
◁ |
[ASAHI KASEI]
[AK4543]
General Description
nAC Â97 Connection to the Digital AC Â97 controller
2AC â97 communicates with its companion AC â97 controller via a digital serial link, âAC-linkâ. All digital audio streams, and
command/status information are communicated over this point to point serial interconnect. A breakout of the signals connecting the
two is shown in the following figure.
ACÂ97
Controller
ACÂ97
SYNC
BIT_CLK
SDATA_OUT
SDATA_IN
RESET#
nACÂ97 Digital Interface
The AK4543 incorporates a 5 pin digital serial interface that links it to the AC â97 controller. AC-link is a bi-directional, fixed
rate(48kHz), serial PCM digital stream. It handles multiple input, and output audio streams, as well as control register accesses
employing a time division multiplexed (TDM) scheme. The AC-link architecture divides each audio frame into 12 outgoing and 12
incoming data streams, each with 20-bit sample resolution. DAC and ADC resolution of the AK4543 is 18 bit resolution. The data
streams currently defined by the AC â97 specification include:
l PCM Playback
2 output slots
2 channel composite PCM output stream
l PCM Record data
2 input slots
2 channel composite PCM input stream
l Control
2 output slot
Control register write port
l Status
2 input slots
Control register read port
SYNC, fixed at 48 KHz, is derived by dividing down the serial bit clock (BIT_CLK). BIT_CLK, fixed at 12.288 MHz, provides the
necessary clocking granularity to support 12, 20-bit outgoing and incoming time slots. AC-link serial data is transitioned on each rising
edge of BIT_CLK. The receiver of AC-link data, the AK4543 for outgoing data and AC â97 controller for incoming data, samples each
serial bit on the falling edges of BIT_CLK.
The AK4543 outputs BIT_CLK when it is assigned as Primary codec by the codec ID configuration ID1# and ID0#. The other hand, the
AK4543 receives BIT_CLK when assigned as the Secondary codec from the Primary device.
The AC-link protocol provides for a special 16-bit slot (Slot 0) wherein each bit conveys a valid tag for its corresponding time slot
within the current audio frame. A â1â in a given bit position of slot 0 indicates that the corresponding time slot within the current audio
frame has been assigned to a data stream, and contains valid data. If a slot is âTaggedâ invalid, it is the responsibility of the source
of the data, (The AK4543 for the input stream, AC â97 controller for the output stream), to stuff all bit positions with 0âs during that slotâs
active time.
SYNC remains high for a total duration of 16 BIT_CLKs at the beginning of each audio frame. The portion of the audio frame where
SYNC is high is defined as the âTag Phaseâ. The remainder of the audio frame where SYNC is low is defined as the âData Phaseâ.
Note that SDATA_OUT and SDATA_IN data is delayed one BIT_CLK because ACÂ97 controller causes
S Y N C signal high at a rising edge of BIT_C L K which initiates a frame.
ÂOutput stream means the direction from AC Â97 controller to the AK4543, and ÂInput stream means the direction
from the AK4543 to ACÂ97 controller
2All the following sentences written with small italic font in this document quote the ACâ97 component specification.
<M0046-E-01>
- 11 -
1999/01
|
▷ |