CC2650_16 Datasheet, PDF (8/59 Pages) Texas Instruments – Multistandard Wireless MCU

CC2650
SWRS158A – FEBRUARY 2015 – REVISED OCTOBER 2015
www.ti.com
Table 4-1. Signal Descriptions – RGZ Package (continued)
NAME
DIO_12
DIO_13
DIO_14
DIO_15
DIO_16
DIO_17
DIO_18
DIO_19
DIO_20
DIO_21
DIO_22
DIO_23
DIO_24
DIO_25
DIO_26
DIO_27
DIO_28
DIO_29
DIO_30
JTAG_TMSC
JTAG_TCKC
RESET_N
RF_P
RF_N
VDDR
VDDR_RF
VDDS
VDDS2
VDDS3
VDDS_DCDC
X32K_Q1
X32K_Q2
X24M_N
X24M_P
EGP
NO.
TYPE
DESCRIPTION
18
Digital I/O
GPIO
19
Digital I/O
GPIO
20
Digital I/O
GPIO
21
Digital I/O
GPIO
26
Digital I/O
GPIO, JTAG_TDO, high-drive capability
27
Digital I/O
GPIO, JTAG_TDI, high-drive capability
28
Digital I/O
GPIO
29
Digital I/O
GPIO
30
Digital I/O
GPIO
31
Digital I/O
GPIO
32
Digital I/O
GPIO
36
Digital/Analog I/O GPIO, Sensor Controller, Analog
37
Digital/Analog I/O GPIO, Sensor Controller, Analog
38
Digital/Analog I/O GPIO, Sensor Controller, Analog
39
Digital/Analog I/O GPIO, Sensor Controller, Analog
40
Digital/Analog I/O GPIO, Sensor Controller, Analog
41
Digital/Analog I/O GPIO, Sensor Controller, Analog
42
Digital/Analog I/O GPIO, Sensor Controller, Analog
43
Digital/Analog I/O GPIO, Sensor Controller, Analog
24
Digital I/O
JTAG TMSC, high-drive capability
25
Digital I/O
JTAG TCKC
35
Digital input Reset, active-low. No internal pullup.
1
RF I/O
Positive RF input signal to LNA during RX
Positive RF output signal to PA during TX
2
RF I/O
Negative RF input signal to LNA during RX
Negative RF output signal to PA during TX
45
Power
1.7-V to 1.95-V supply, typically connect to output of internal DC-DC⁽³⁾⁽²⁾
48
Power
1.7-V to 1.95-V supply, typically connect to output of internal DC-DC⁽⁴⁾⁽²⁾
44
Power
1.8-V to 3.8-V main chip supply⁽¹⁾
13
Power
1.8-V to 3.8-V DIO supply⁽¹⁾
22
Power
1.8-V to 3.8-V DIO supply⁽¹⁾
34
Power
1.8-V to 3.8-V DC-DC supply
3
Analog I/O
32-kHz crystal oscillator pin 1
4
Analog I/O
32-kHz crystal oscillator pin 2
46
Analog I/O
24-MHz crystal oscillator pin 1
47
Analog I/O
24-MHz crystal oscillator pin 2
Power
Ground – Exposed Ground Pad
(3) If internal DC-DC is not used, this pin is supplied internally from the main LDO.
(4) If internal DC-DC is not used, this pin must be connected to VDDR for supply from the main LDO.
8
Terminal Configuration and Functions
Submit Documentation Feedback
Product Folder Links: CC2650
Copyright © 2015, Texas Instruments Incorporated