TCA9534_16 Datasheet, PDF (5/38 Pages) Texas Instruments – Low Voltage 8-Bit I2C and SMBUS Low-Power I/O Expander with Interrupt Output and Configuration Registers

www.ti.com
TCA9534
SCPS197B – SEPTEMBER 2014 – REVISED NOVEMBER 2016
6.4 Thermal Information
THERMAL METRIC⁽¹⁾
TCA9534
PW (TSSOP)
DW (SOIC)
UNIT
16 PINS
16 PINS
R_θJA
R_θJC(top)
R_θJB
ψ_JT
ψ_JB
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
Junction-to-top characterization parameter
Junction-to-board characterization parameter
122
92.2
°C/W
56.4
53.8
°C/W
67.1
56.9
°C/W
10.8
26.4
°C/W
66.5
56.4
°C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
6.5 Electrical Characteristics
over operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
V_IK
V_PORR
V_PORF
Input diode clamp voltage
Power-on reset voltage,
V_CC rising
Power-on reset voltage,
V_CC falling
I_I = –18 mA
V_I = V_CC or GND, I_O = 0
V_I = V_CC or GND, I_O = 0
I_OH = –8 mA
V_OH
P-port high-level output
voltage ⁽²⁾
I_OH = –10 mA
SDA ⁽³⁾
I_OL
P port⁽⁴⁾
INT ⁽⁵⁾
SCL, SDA
I_I
A0, A1, A2
I_IH
P port
I_IL
P port
V_OL = 0.4 V
V_OL = 0.5 V
V_OL = 0.7 V
V_OL = 0.4 V
V_I = V_CC or GND
V_I = V_CC
V_I = GND
V_CC
1.65 V to 5.5 V
MIN TYP⁽¹⁾ MAX UNIT
–1.2
V
1.2 1.5 V
0.75
1.65 V
1.2
2.3 V
1.8
3V
2.6
4.5 V
4.1
1.65 V
1
2.3 V
1.7
3V
2.5
4.5 V
4
1.65 V to 5.5 V
3
1.65 V to 5.5 V
8
1.65 V to 5.5 V
10
1.65 V to 5.5 V
3
1.65 V to 5.5 V
1.65 V to 5.5 V
1.65 V to 5.5 V
1
V
V
mA
±1
µA
±1
1 µA
–1 µA
(1) All typical values are at nominal supply voltage (1.8-, 2.5-, 3.3-, or 5-V V_CC) and T_A = 25°C.
(2) Each P-port I/O configured as a high output must be externally limited to a maximum of 10 mA, and the total current sourced by all I/Os
(P-ports P7-P0) through V_CC must be limited to a maximum current of 80 mA.
(3) The SDA pin must be externally limited to a maximum of 12 mA, and the total current sunk by all I/Os (P-ports P7-P0, INT, and SDA)
through GND must be limited to a maximum current of 200 mA.
(4) Each P-port I/O configured as a low output must be externally limited to a maximum of 25 mA, and the total current sunk by all I/Os (P-
ports P7-P0, INT, and SDA) through GND must be limited to a maximum current of 200 mA.
(5) The INT pin must be externally limited to a maximum of 7 mA, and the total current sunk by all I/Os (P-ports P7-P0, INT, and SDA)
through GND must be limited to a maximum current of 200 mA.
Copyright © 2014–2016, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: TCA9534