CC1350 Datasheet, PDF (14/52 Pages) Texas Instruments – SimpleLink Ultra-Low-Power Dual-Band Wireless MCU

CC1350
SWRS183 – JUNE 2016
www.ti.com
5.8 1-Mbps GFSK (Bluetooth low energy) – RX
Measured on the TI CC1350_7XD-Dual Band reference design with T_c = 25°C, V_DDS = 3.0 V, f_RF = 2440 MHz, unless
otherwise noted. All tests with Bluetooth low energy PHY (1 Mbps), 37 byte payload unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
Differential mode. Measured at the
Receiver sensitivity
CC1350_7XD-Dual Band SMA connector, 37
–87
byte payload BER = 10^–3
Differential mode. Measured at the
Receiver sensitivity
CC1350_7XD-Dual Band SMA connector, 255
-86
byte payload BER = 10^–3
Differential mode. Measured at the
Receiver saturation
CC1350_7XD-Dual Band SMA connector, BER
0
= 10^–3
Difference between the incoming carrier
Frequency error tolerance
frequency and the internally generated carrier
frequency. Input signal 10 dB above sensitivity
–350
350
limit
Difference between incoming data rate and the
Data rate error tolerance
internally generated data rate. Input signal 10
–750
750
dB above sensitivity limit
Co-channel rejection⁽¹⁾
Wanted signal at –67 dBm, modulated interferer
in channel, BER = 10^–3
–6
Selectivity, ±1 MHz⁽¹⁾
Wanted signal at –67 dBm, modulated interferer
at ±1 MHz, BER = 10^–3
7 / 4 ⁽²⁾
Selectivity, +2 MHz⁽¹⁾
Wanted signal at –67 dBm, modulated interferer
at +2 MHz, BER = 10^–3
38
Selectivity, ±3 MHz⁽¹⁾
Wanted signal at –67 dBm, modulated interferer
at ±3 MHz, BER = 10^–3 Note that -3 MHz is -1
MHz from the image frequency.
36 / 41⁽²⁾
Selectivity, ±4 MHz⁽¹⁾
Wanted signal at –67 dBm, modulated interferer
at ±4 MHz, BER = 10^–3
39 / 38⁽²⁾
Selectivity, ±5 MHz⁽¹⁾
Wanted signal at –67 dBm, modulated interferer
at ±5 MHz, BER = 10^–3
35 / 39⁽²⁾
Selectivity, ±6 MHz⁽¹⁾
Wanted signal at –67 dBm, modulated interferer
at ≥ ±6 MHz, BER = 10^–3
42 / 37⁽²⁾
Selectivity, ±15 MHz or more⁽¹⁾
Wanted signal at –67 dBm, modulated interferer
at ≥ ±15 MHz or more, BER = 10^–3
55
Selectivity, Image frequency
(image compensation enabled, Wanted signal at –67 dBm, modulated interferer
the image compensation is
at image frequency, BER = 10^–3
37
calibrated in production)⁽¹⁾
Selectivity, Image frequency
±1 MHz⁽¹⁾
Out-of-band blocking⁽³⁾
Wanted signal at –67 dBm, modulated interferer
at ±1 MHz from image (-3 MHz and -1 MHz from
wanted) frequency, BER = 10^–3
30 MHz to 2000 MHz
4 / 41⁽²⁾
–25
Out-of-band blocking
2003 MHz to 2399 MHz
>–20
Out-of-band blocking
2484 MHz to 2997 MHz
>–20
Out-of-band blocking
3000 MHz to 12.75 GHz
>–30
Wanted signal at 2402 MHz, –64 dBm. Two
Intermodulation
interferers at 2405 and 2408 MHz, respectively,
–30
at the given power level
Conducted measurement in a 50-Ω single-ended
Spurious emissions,
30 to 1000 MHz
load. Suitable for systems targeting compliance
with EN 300 328, EN 300 440 class 2, FCC
–72
CFR47, Part 15 and ARIB STD-T-66
UNIT
dBm
dBm
dBm
kHz
ppm
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dBm
dBm
dBm
dBm
dBm
dBm
(1) Numbers given as I/C dB.
(2) X / Y, where X is +N MHz and Y is –N MHz.
(3) Excluding one exception at F_wanted / 2, per Bluetooth Specification.
14
Specifications
Submit Documentation Feedback
Product Folder Links: CC1350
Copyright © 2016, Texas Instruments Incorporated