LM3S9B90 Datasheet, PDF (788/1185 Pages) Texas Instruments – Stellaris® LM3S9B90 Microcontroller

Controller Area Network (CAN) Module
19.3.5
note that in order for these bits to be used for acceptance filtering, they must be enabled by
setting the UMASK bit in the CANIFnMCTL register.
3. In the CANIFnMSK2 register, use the MSK[12:0] bits to specify which of the bits in the 29-bit
or 11-bit message identifier are used for acceptance filtering. Note that MSK[12:0] are used
for bits [28:16] of the 29-bit message identifier; whereas MSK[12:2] are used for bits [10:0] of
the 11-bit message identifier. Use the MXTD and MDIR bits to specify whether to use XTD and
DIR for acceptance filtering. A value of 0x00 enables all messages to pass through the
acceptance filtering. Also note that in order for these bits to be used for acceptance filtering,
they must be enabled by setting the UMASK bit in the CANIFnMCTL register.
4. For a 29-bit identifier, configure ID[15:0] in the CANIFnARB1 register to are used for bits
[15:0] of the message identifier and ID[12:0] in the CANIFnARB2 register to are used for
bits [28:16] of the message identifier. Set the XTD bit to indicate an extended identifier; set the
DIR bit to indicate transmit; and set the MSGVAL bit to indicate that the message object is valid.
5. For an 11-bit identifier, disregard the CANIFnARB1 register and configure ID[12:2] in the
CANIFnARB2 register to are used for bits [10:0] of the message identifier. Clear the XTD bit to
indicate a standard identifier; set the DIR bit to indicate transmit; and set the MSGVAL bit to
indicate that the message object is valid.
6. In the CANIFnMCTL register:
■ Optionally set the UMASK bit to enable the mask (MSK, MXTD, and MDIR specified in the
CANIFnMSK1 and CANIFnMSK2 registers) for acceptance filtering
■ Optionally set the TXIE bit to enable the INTPND bit to be set after a successful transmission
■ Optionally set the RMTEN bit to enable the TXRQST bit to be set on the reception of a matching
remote frame allowing automatic transmission
■ Set the EOB bit for a single message object
■ Configure the DLC[3:0] field to specify the size of the data frame. Take care during this
configuration not to set the NEWDAT, MSGLST, INTPND or TXRQST bits.
7. Load the data to be transmitted into the CAN IFn Data (CANIFnDA1, CANIFnDA2, CANIFnDB1,
CANIFnDB2) registers. Byte 0 of the CAN data frame is stored in DATA[7:0] in the CANIFnDA1
register.
8. Program the number of the message object to be transmitted in the MNUM field in the CAN IFn
Command Request (CANIFnCRQ) register.
9. When everything is properly configured, set the TXRQST bit in the CANIFnMCTL register. Once
this bit is set, the message object is available to be transmitted, depending on priority and bus
availability. Note that setting the RMTEN bit in the CANIFnMCTL register can also start message
transmission if a matching remote frame has been received.
Updating a Transmit Message Object
The CPU may update the data bytes of a Transmit Message Object any time via the CAN Interface
Registers and neither the MSGVAL bit in the CANIFnARB2 register nor the TXRQST bits in the
CANIFnMCTL register have to be cleared before the update.
788
June 14, 2010
Texas Instruments-Advance Information