English
Language : 

BQ24030_07 Datasheet, PDF (6/38 Pages) Texas Instruments – SINGLE-CHIP CHARGE AND SYSTEM POWER-PATH MANAGEMENT IC (bqTINY)
bq24030, bq24031, bq24032A
bq24035, bq24038
SLUS618F – AUGUST 2004 – REVISED NOVEMBER 2006
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
over junction temperature range (0°C ≤ TJ ≤ 125°C) and the recommended supply voltage range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
USB PIN INPUT CURRENT REGULATION
I(USB)
USB input current range,
bq24030/32A/35/38 (11)
VI(BAT) > V(LOWV),
VI(USB) - VI(BAT) > V(DO-MAX), ISET2= Low,
PSEL = Low, or no AC (12)
VI(BAT) > V(LOWV),
VI(USB) - VI(BAT) > V(DO-MAX), ISET2= High,
400
PSEL = Low, or no AC (11)
100
mA
500
BAT PIN CHARGING VOLTAGE REGULATION, VO (BAT-REG) + V (DO-MAX) < VCC, ITERM < IBAT(OUT) ≤ 1 A
bq24030/32A/35
VO(BAT-REG)
Battery
charge
voltage
bq24031
bq24038
VBSEL = HI
VBSEL = LO
4.2
4.1
V
4.36
4.2
Battery charge voltage regulation TA = 25°C
accuracy
–0.5%
–1%
0.5%
1%
CHARGE TERMINATION DETECTION
I(TERM)
V(TERM-AC)
Charge termination detection
range
AC-charge termination detection
voltage, measured on ISET1
VI(BAT) < V(RCH),
I(TERM) = (K(SET) × V(TERM))/ RSET
VI(BAT) > V(RCH) , PSEL = High,
ACPG = Low
10
150 mA
235
250
265 mV
V(TAPER-USB)
USB-charge termination detection VI(BAT) > V(RCH), PSEL = Low or
voltage, measured on ISET1
PSEL = High and ACPG = High
95
100
130 mV
TDGL(TERM)
Deglitch time for termination
detection
tFALL = 100 ns, 10 mV overdrive,
ICHG increasing above or decreasing
below threshold
22.5
ms
TEMPERATURE SENSE COMPARATORS
VLTF
VHTF
ITS
TDGL(TF)
High voltage threshold
Temp fault at V(TS) > VLTF
Low voltage threshold
Temp fault at V(TS) < VHTF
Temperature sense current source
Deglitch time for temperature fault
detection (13)
R(TMR) = 50 kΩ, VI(BAT) increasing or
decreasing above and below;
100-ns fall time, 10-mv overdrive
2.465
0.485
94
2.500
0.500
100
22.5
2.535
V
0.515
V
106
µA
ms
BATTERY RECHARGE THRESHOLD
VRCH
Recharge threshold voltage
VO(BAT-REG)
–0.075
VO(BAT-REG)
–0.100
VO(BAT-REG)
–0.125
V
TDGL(RCH)
Deglitch time for recharge
detection (13)
R(TMR) = 50 kΩ, VI(BAT) increasing
or decreasing below threshold,
100-ns fall time, 10-mv overdrive
22.5
ms
(11) With the PSEL= low, the bqTINY III-series defaults to USB charging. If USB input is ≤ VBAT, then the bqTINY III-series charges from the
AC input at the USB charge rate. In this configuration, the specification is 400 mA (min) and 500 mA (max).
(12) With the PSEL= low, the bqTINY III-series defaults to USB charging. If USB input is ≤ VBAT, then the bqTINY III-series charges from the
AC input at the USB charge rate. In this configuration, the specification is 80 mA (min) and 100 mA (max).
(13) All deglitch periods are a function of the timer setting and is modified in DPPM or thermal regulation modes by the percentages that the
program current is reduced.
6
Submit Documentation Feedback