TMS320VC33 Datasheet, PDF (25/57 Pages) Texas Instruments – DIGITAL SIGNAL PROCESSOR

TMS320VC33
DIGITAL SIGNAL PROCESSOR
SPRS087E − FEBRUARY 1999 − REVISED JANUARY 2004
absolute maximum ratings over specified temperature range (unless otherwise noted)^†
Supply voltage range, DV_DD^‡ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 4 V
Supply voltage range, CV_DD^‡ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 2.4 V
Input voltage range, V_I^§ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −1 V to 4.6 V
Output voltage range, V_O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 4.6 V
Continuous power dissipation (worst case)^¶ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 mW
(for TMS320VC33-150)
Operating case temperature range, T_C (PGE − commercial) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 90°C
T_C (PGEA − industrial) . . . . . . . . . . . . . . . . . . . . . . . . . − 40°C to 100°C
Storage temperature range, T_stg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . − 55°C to 150°C
† _{Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and}
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
‡ _{All voltage values are with respect to VSS.}
§ _{Absolute DC input level should not exceed the DVDD or VSS supply rails by more than 0.3 V. An instantaneous low current pulse of < 2 ns,}
< 10 mA, and < 1 V amplitude is permissible.
¶ _{Actual operating power is much lower. This value was obtained under specially produced worst-case test conditions for the TMS320VC33, which}
are not sustained during normal device operation. These conditions consist of continuous parallel writes of a checkerboard pattern to the external
data and address buses at the maximum possible rate with a capacitive load of 30 pF. See normal (ICC) current specification in the electrical
characteristics table and also read TMS320C3x General-Purpose Applications User’s Guide (literature number SPRU194).
recommended operating conditions^‡#||
CVDD Supply voltage for the core CPU^k
DVDD Supply voltage for the I/O pinsh
MIN
NOM
MAX
UNIT
1.71
1.8
1.89
V
3
3.3
3.6
V
VSS
VIH
VIL
Supply ground
High-level input voltage
Low-level input voltage
0.7 * DVDD
− 0.3§
0
V
DVDD + 0.3§
V
0.3 * DVDD
V
IOH High-level output current
IOL Low-level output current
4
mA
4
mA
Operating case temperature (commercial)
TC
Operating case temperature (industrial)
0
90
°C
−40
100
CL
Capacitive load per output pin
30
pF
‡ _{All voltage values are with respect to VSS.}
§ _{Absolute DC input level should not exceed the DVDD or VSS supply rails by more than 0.3 V. An instantaneous low current pulse of < 2 ns, < 10 mA,}
and < 1 V amplitude is permissible.
# _{All inputs and I/O pins are configured as inputs.}
|| _{All input and I/O pins use a Schmitt hysteresis inputs except SHZ and D0−D31. Hysteresis is approximately 10% of DVDD and is centered at}
0.5 * DVDD.
kCVDD should not exceed DVDD by more than 0.7 V. (Use a Schottky clamp diode between these supplies.)
hDVDD should not exceed CVDD by more than 2.5 V.
• POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
25