MSP430FE42X2 Datasheet, PDF (17/48 Pages) Texas Instruments – MIXED SIGNAL MICROCONTROLLER

MSP430FE42x2
MIXED SIGNAL MICROCONTROLLER
SLAS616 − JULY 2008
absolute maximum ratings^†
Voltage applied at V_CC to V_SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to + 4.1 V
Voltage applied to any pin (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to V_CC + 0.3 V
Diode current at any device terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±2 mA
Storage temperature (unprogrammed device) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 150°C
Storage temperature (programmed device) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 85°C
† _{Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and}
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltages referenced to V_SS. The JTAG fuse-blow voltage, V_FB, is allowed to exceed the absolute maximum rating. The voltage is
applied to the TDI/TCLK pin when blowing the JTAG fuse.
recommended operating conditions (see Note 1)
PARAMETER
MIN NOM MAX UNITS
Supply voltage during program execution; ESP430 and SD16 disabled,
V_CC (AV_CC = DV_CC = V_CC) (see Note 1)
1.8
3.6 V
Supply voltage during program execution; SVS enabled, PORON = 1, ESP430 and SD16 disabled,
V_CC (AV_CC = DV_CC = V_CC) (see Note 1 and Note 2)
2.0
3.6 V
Supply voltage during program execution; ESP430 or SD16 enabled or during programming of
flash memory, V_CC (AV_CC = DV_CC = V_CC) (see Note 1)
2.7
3.6 V
Supply voltage (see Note 1), V_SS (AV_SS = DV_SS = V_SS)
Operating free-air temperature range, T_A
LF selected, XTS_FLL=0
Watch crystal
0
−40
32768
0V
85 °C
Hz
LFXT1 crystal frequency, f_(LFXT1) (see Note 3) XT1 selected, XTS_FLL=1
XT1 selected, XTS_FLL=1
Ceramic resonator
Crystal
450
1000
8000 kHz
8000 kHz
Processor frequency (signal MCLK), f_(System) (see Note 4)
V_CC = 2.7 V
dc
V_CC = 3.6 V
dc
8.4
MHz
8.4
NOTES: 1. It is recommended to power AV_CC and DV_CC from the same source. A maximum difference of 0.3 V between AV_CC and DV_CC can
be tolerated during power up and operation.
2. The minimum operating supply voltage is defined according to the trip point where POR is going active by decreasing supply voltage.
POR is going inactive when the supply voltage is raised above minimum supply voltage plus the hysteresis of the SVS circuitry.
3. The LFXT1 oscillator in LF-mode requires a watch crystal.
4. For frequencies above 8 MHz, MCLK is sourced by the built-in oscillator (DCO and FLL+).
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265
17