SKYPER42R Datasheet, PDF (1/18 Pages) Semikron International – IGBT Driver Core

SKYPER 42 R
Absolute Maximum Ratings
Symbol Conditions
Values
Unit
SKYPER^®
IGBT Driver Core
SKYPER 42 R
Preliminary Data
Features
• Two output channels
• Integrated potential free power supply
• Under voltage protection
• Drive interlock top / bottom
• Dynamic short cirucit protection
• Shut down input
• Failure management
• IEC 60068-1 (climate) 40/085/56, no
condensation and no dripping water
permitted, non-corrosive, climate class
3K3 acc. EN60721
Typical Applications*
• Driver for IGBT modules in bridge
circuits in industrial application
• DC bus voltage up to 1200V
Footnotes
Isolation test voltage with external high
voltage diode
The isolation test is not performed as a
series test at SEMIKRON
The driver power can be expanded to 50µC
with external boost capacitors
Isolation coordination in compliance with
EN50178 PD2
Operating temperature is real ambient
temperature around the driver core
Degree of protection: IP00
V_s
V_iH
V_iL
Iout_PEAK
Iout_AVmax
f_max
V_CE
dv/dt
V_{isol IO}
V_isolPD
V_isol12
R_{Gon min}
R_{Goff min}
Q_out/pulse
T_op
T_stg
Supply voltage primary
Input signal voltage (HIGH)
Input signal voltage (LOW)
Output peak current
Output average current
Max. switching frequency
Collector emitter voltage sense across
the IGBT
Rate of rise and fall of voltage
secondary to primary side
Isolation test voltage input - output (AC,
rms, 2s)
Partial discharge extinction voltage,
rms, Q_PD ̞ 10pC
Isolation test voltage output 1 - output 2
(AC, rms, 2s)
Minimum rating for external R_Gon
Minimum rating for external R_Goff
Max. rating for output charge per pulse
Operating temperature
Storage temperature
16
Vs + 0.3
GND - 0.3
30
150
100
1700
100
4000
1500
1500
0.8
0.8
50
-40 ... 85
-40 ... 85
V
V
V
A
mA
kHz
V
kV/µs
V
V
V
:
:
µC
°C
°C
Characteristics
Symbol Conditions
min.
typ.
max. Unit
V_s
Supply voltage primary side
I_SO
Supply current primary (no load)
14.4
15
15.6
V
125
mA
Supply current primary side (max.)
800
mA
V_i
Input signal voltage on / off
15 / 0
V
V_IT+
Input treshold voltage HIGH
12.3
V
V_IT-
Input threshold voltage (LOW)
4.6
V
R_IN
Input resistance (switching/HALT
signal)
10
k:
V_G(on)
Turn on output voltage
15
V
V_G(off)
Turn off output voltage
-8
V
f_ASIC
Asic system switching frequency
8
MHz
t_d(on)IO
Input-output turn-on propagation time
1.1
µs
t_d(off)IO
Input-output turn-off propagation time
1.1
µs
t_d(err)
Error input-output propagation time
2.3
µs
t_pERRRESET Error reset time
9
µs
t_TD
Top-Bot interlock dead time
2
µs
C_ps
Coupling capacitance prim sec
w
weight
3
pF
g
MTBF
2.1
10⁶h
This is an electrostatic discharge sensitive device (ESDS), international standard IEC 60747-1,
Chapter IX
* The specifications of our components may not be considered as an assurance of component
characteristics. Components have to be tested for the respective application. Adjustments may
be necessary. The use of SEMIKRON products in life support appliances and systems is
subject to prior specification and written approval by SEMIKRON. We therefore strongly
recommend prior consultation of our staff.
Driver Core
© by SEMIKRON
Rev. 5 – 05.04.2011
1