|
LC87F2708A Datasheet, PDF (2/21 Pages) Sanyo Semicon Device – CMOS IC FROM 8K byte, RAM 512 byte on-chip 8-bit 1-chip Microcontroller | |||
|
◁ |
LC87F2708A
ÂMinimum Bus Cycle Time Note1
⢠100ns (10MHz)
VDD=2.7 to 5.5V Note2
ÂMinimum Instruction Cycle Time
⢠300ns (10MHz)
VDD=2.7 to 5.5V Note2
Note1: The bus cycle time here refers to the ROM read speed.
Note2: Use this product in a voltage range of 3.0 to 5.5V because the minimum release voltage (PORRL) of the
power-on reset (POR) circuit is 2.87V±0.12V.
ÂPorts
⢠I/O ports
Ports whose I/O direction can be designated in 1-bit units 11 (P10 to P16, P30 to P33)
⢠Reset pins
1 (RES)
⢠Power pins
2 (VSS1, VDD1)
ÂTimers
⢠Timer 0: 16-bit timer/counter with a capture register.
Mode 0: 8-bit timer with an 8-bit programmable prescaler (with an 8-bit capture register) Ã 2 channels
Mode 1: 8-bit timer with an 8-bit programmable prescaler (with an 8-bit capture register)
+ 8-bit counter (with an 8-bit capture register)
Mode 2: 16-bit timer with an 8-bit programmable prescaler (with a 16-bit capture register)
Mode 3: 16-bit counter (with a 16-bit capture register)
⢠Timer 1: 16-bit timer/counter that can provide with PWM/toggle outputs
Mode 0: 8-bit timer with an 8-bit prescaler (with toggle outputs) + 8-bit timer/
counter with an 8-bit prescaler (with toggle outputs)
Mode 1: 8-bit PWM with an 8-bit prescaler à 2 channels
Mode 2: 16-bit timer/counter with an 8-bit prescaler (with toggle outputs)
(toggle output also possible from the lower-order 8 bits)
Mode 3: 16-bit timer with an 8-bit prescaler (with toggle outputs)
ÂSerial Interface
(Lower-order 8 bits may be used as PWM)
⢠SIO7: 8-bit synchronous serial interface
1) LSB first/MSB first mode selectable
2) Built-in 8-bit baudrate generator (maximum transfer clock cycle=4/3 tCYC)
ÂHigh-Speed 12-bit PWM
⢠System clock/high-speed RC oscillation clock (20MHz or 40MHz) operation selectable
⢠Duty/period programmable
⢠Continuous PWM output/specific count PWM output (automatic stop) selectable
 High-speed Pulse/Period Counter
⢠HCT1: High-speed RC pulse width/period counter 1
1) System clock/high-speed RC oscillation clock (20MHz or 40MHz) operation selectable
2) H-level width/L-level width/period measurement modes selectable
3) Input triggering noise filter
⢠HCT2: High-speed pulse width/period counter 2
1) System clock/high-speed RC oscillation clock (20MHz or 40MHz) operation selectable
2) Can measure both L-level width and period simultaneously.
3) Input triggering noise filter
4) Input trigger selectable (from 3 signals, i.e., P11/HCT2IN, P31/HCT2IN, and analog comparator output)
ÂAD Converter: 12 bits à 7 channels
⢠12-/8-bits AD converter resolution selectable
ÂAnalog Comparator
⢠Sends output to the P32/CMPO port (polarity selectable).
⢠Edge detection function (shared with INTC and also allows the selection of the noise filter function)
No.A1335-2/21
|
▷ |