DS17H732S Datasheet, PDF (10/20 Pages) Sanyo Semicon Device – 3-PHASE STEPPING SYSTEMS

3-phase STEPPING SYSTEMS
Stepping motor Specifications
3-phase stepping motor
42 ^{mm sqʢ. 1.65 inch sq.ʣ}
103H533 ˘
1.2˃/step HB type
Model
Single shaft
Double shafts
103H5332-0340 -0310
103H5333-0340 -0310
Holding torque at 2-phase
energization
[Nɾmʢozɾin ʣMIN.]
0.196Ê¢27.75Ê£
0.265Ê¢37.53Ê£
Rated current
A/phaseɹ
3
3
Wiring resistance
Њ /phase
0.84
0.94
Winding inductance
mH/phase
0.5
0.5
Rotor inertia
MassʢWeightʣ
[Ê·10^{- 4}kgɾmÊ¢² ozɾin² Ê£] [kgÊ¢IbsÊ£]
0.053Ê¢0.29Ê£
0.3Ê¢0.66Ê£
0.065Ê¢0.36Ê£
0.38Ê¢0.84Ê£
˙ Dimensions [unit : mmʢinchʣ]
15±1
(.59±.04)
L±0.5
(1.54±.02)
24±0.5
(.94±.02)
1.5
(.06)
c42±0.25
(c1.65±.01)
4–31±0.25
(4-1.22±.01)
18(.71) MAX.
Pin number
12 3
Set part number Motor model number
DS17H5 32 ˚
DS17H5 3 3 ˚
103H5332-03˚ 0
103H5333-03˚ 0
˚ indicates motor shaft specification
˚ɿMotor shaft spec
Motor shaft spec Set part number
Single shaft
S
Double shafts
D
4–M3ʷ0.5(4 – M3ʷ02)
Effective tapping depth: 4 MIN.
Motor lengthʢLʣ
39 mmʢ1.54 inchʣ
48 mmʢ1.89 inchʣ
Motor model number
4
1
˙ Pulse rate-torque characteristics
˙ 103H5332-0340
˙ 103H5333-0340
70
5
0.5
70
5
0.5
60
4
0.4
50
40
3
0.3
30
2
0.2
20
1
0.1
10
Pull-out torque at JL1
Starting torque at JL2
60
4
0.4
50
40
3
0.3
30
2
0.2
20
1
0.1
10
Pull-out torque at JL1
Starting torque at JL2
0
0
0
0.1
1
10
Pulse rate(kpulse/s)
100
1000 2000 3000 5000
Number of rotations(min-1)
100
0
0
0
0.1
1
10
Pulse rate(kpulse/s)
100
1000 2000 3000 5000
Number of rotations(min-1)
100
Constant current circuit
Source voltage : DC24 Vɾoperating current : 3 A/phase,
2-phase energizationʢfull stepʣ
JL1=[0.94x10^-4kgɾmÊ¢² 5.14ozɾin²Ê£use the rubber coupling.]
JL2=[0.8x10^-4kgɾm²Ê¢4.37ozɾin²Ê£use the direct coupling.]
Constant current circuit
Source voltage : DC24 Vɾoperating current : 3 A/phase,
2-phase energizationʢfull stepʣ
JL1=[0.94x10-4kgɾmÊ¢² 5.14ozɾin²Ê£use the rubber coupling.]
JL2=[0.8x10-4kgɾmÊ¢² 4.37ozɾin²Ê£use the direct coupling.]
The date are measured under the drive condition of our company. The drive torque may very depending on the accuracy of customer-side equipment.
9