|
K4T1G044QM Datasheet, PDF (24/29 Pages) Samsung semiconductor – 1Gb M-die DDR2 SDRAM Specification | |||
|
◁ |
1Gb M-die DDR2 SDRAM
DDR2 SDRAM
Specific Notes for dedicated AC parameters
9. User can choose which active power down exit timing to use via MRS(bit 12). tXARD is expected to be
used for fast active power down exit timing. tXARDS is expected to be used for slow active power down exit
timing.
10. AL = Additive Latency
11. This is a minimum requirement. Minimum read to precharge timing is AL + BL/2 providing the tRTP and
tRAS(min) have been satisfied.
12. A minimum of two clocks (2 * tCK) is required irrespective of operating frequency
13. Timings are guaranteed with command/address input slew rate of 1.0 V/ns.
14. These parameters guarantee device behavior, but they are not necessarily tested on each device. They
may be guaranteed by device design or tester correlation.
15. Timings are guaranteed with data, mask, and (DQS/RDQS in singled ended mode) input slew rate of 1.0
V/ns.
16. Timings are guaranteed with CK/CK differential slew rate of 2.0 V/ns. Timings are guaranteed for DQS
signals with a differential slew rate of 2.0 V/ns in differential strobe mode and a slew rate of 1V/ns in single
ended mode.
17. tDS and tDH derating for DDR2-400 and DDR2-533
âtDS, âtDH Derating Values (ALL units in âpsâ, Note 1 applies to entire Table)
DQS,DQS Differential Slew Rate
2.0
1.5
1.0
DQ 0.9
Slew
rate
0.8
V/ns 0.7
0.6
0.5
0.4
4.0 V/ns
âtD âtD
SH
125 45
83 21
00
--
--
--
--
--
--
3.0 V/ns
âtD âtD
SH
125 45
83 21
00
-11 -14
-
-
-
-
-
-
-
-
-
-
2.0 V/ns
âtD âtD
SH
125 45
83 21
00
-11 -14
-25 -31
-
-
-
-
-
-
-
-
1.8 V/ns
âtD âtD
SH
--
95 33
12 12
1 -2
-13 -19
-31 -42
--
--
--
1.6 V/ns
âtD âtD
SH
--
--
24 24
13 10
-1 -7
-19 -30
-43 -59
--
--
1.4V/ns 1.2V/ns 1.0V/ns 0.8V/ns
âtD âtD âtD âtD âtD âtD âtD âtD
SHSHSHSH
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
25 22 -
-
-
-
-
-
11 5 23 17 -
-
-
-
-7 -18 5 -6 17 6 - -
-31 -47 -19 -35 -7 -23 5 -11
-74 -89 -62 -77 -50 -65 -38 -53
- - -127 -140 -115 -128 -103 -116
For all input signals the total tDS (setup time) and tDH (hold time) required is calculated by adding the
datasheet tDS(base) and tDH(base) value to the delta tDS and delta tDH derating value respectively. Exam-
ple: tDS (total setup time) = tDS(base) + delta tDS.
Page 24 of 29
Rev.1.1 Jan. 2005
|
▷ |