M16C64C_15 Datasheet, PDF (72/91 Pages) Renesas Technology Corp – RENESAS MCU

M16C/64C Group
5. Electrical Characteristics
Table 5.40 Electrical Characteristics (3)
V_CC1 = V_CC2 = 3 V
R5F3640KCNFA, R5F3640KCNFB, R5F3640KCDFA, R5F3640KCDFB,
R5F3640MCNFA, R5F3640MCNFB, R5F3640MCDFA, R5F3640MCDFB
V_CC1 = V_CC2 = 2.7 to 3.3 V, V_SS = 0 V at T_opr = −20°C to 85°C/−40°C to 85°C, f_(BCLK) = 25 MHz unless otherwise specified.
Symbol
Parameter
Measuring Condition
I_CC
Power supply current High-speed mode f_(BCLK) = 25 MHz
XIN = 4.2 MHz (square wave),
In single-chip, mode,
PLL multiplied by 6
the output pin are
125 kHz on-chip oscillator stopped
open and other pins
are V_SS
f_(BCLK) = 25 MHz, A/D conversion
XIN = 4.2 MHz (square wave),
PLL multiplied by 6
125 kHz on-chip oscillator stopped
f_(BCLK) = 20 MHz
XIN = 20 MHz (square wave)
125 kHz on-chip oscillator stopped
125 kHz on-chip Main clock stopped
oscillator mode 125 kHz on-chip oscillator on, no division
FMR22 = 1 (slow read mode)
Low-power mode f_(BCLK) = 32 MHz
In low-power mode, FMR 22 = FMR23 = 1
on flash memory ⁽¹⁾
f_(BCLK) = 32 MHz
In low-power mode,
on RAM ⁽¹⁾
Wait mode
Main clock stopped
125 kHz on-chip oscillator on
Peripheral clock operating
T_opr = 25°C
f_(BCLK) = 32 MHz (oscillation capacity High)
125 kHz on-chip oscillator stopped
Peripheral clock operating
T_opr = 25°C
f_(BCLK) = 32 kHz (oscillation capacity Low)
125 kHz on-chip oscillator stopped
Peripheral clock operating
T_opr = 25°C
XIN = 6 MHz
125 kHz on-chip oscillator stopped
Peripheral clock f1 provision disabled except
timers (PCKSTP1A = 1)
Main clock as a timer clock source
(PCKSTP11 = 0, PCKSTP17 = 1)
A given timer operating
Stop mode
Main clock stopped
125 kHz on-chip oscillator stopped
Peripheral clock stopped
T_opr = 25°C
During flash
f_(BCLK) = 10 MHz, PM17 = 1 (one wait)
memory program _{VCC1 = 3.0 V}
During flash
memory erase
f_(BCLK) = 10 MHz, PM17 = 1 (one wait)
V_CC1 = 3.0 V
Standard
Unit
Min. Typ. Max.
22.0
mA
22.7
mA
17.0
mA
500.0
μA
170.0
μA
40.0
μA
20.0
μA
8.0
μA
4.0
μA
0.5
mA
1.6
μA
20.0
mA
30.0
mA
Note:
1. This indicates the memory in which the program to be executed exists.
R01DS0016EJ0110 Rev.1.10
Jul 31, 2012
Page 72 of 88