HYS64T32X00EDL Datasheet, PDF (16/86 Pages) Qimonda AG – 200-Pin SO-DIMM DDR2 SDRAM Modules

Internet Data Sheet
HYS64T[32/64/128]xxxEDL–[25F/…/3.7](–)B2
Small Outlined DDR2 SDRAM Modules
Speed Grade
TABLE 13
Speed Grade Definition Speed Bins for DDR2–667
DDR2–667C
DDR2–667D
Unit
Note
QAG Sort Name
–3
–3S
CAS-RCD-RP latencies
4–4–4
5–5–5
t_CK
Parameter
Symbol
Min.
Max.
Min.
Max.
—
Clock Frequency
@ CL = 3
t_CK
5
8
5
8
ns
1)2)3)4)
@ CL = 4
t_CK
3
8
3.75
8
ns
1)2)3)4)
@ CL = 5
t_CK
3
8
3
8
ns
1)2)3)4)
Row Active Time
t_RAS
45
70000 45
70000 ns
1)2)3)4)5)
Row Cycle Time
t_RC
57
—
60
—
ns
1)2)3)4)
RAS-CAS-Delay
t_RCD
12
—
15
—
ns
1)2)3)4)
Row Precharge Time
t_RP
12
—
15
—
ns
1)2)3)4)
1) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew
Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode.
2) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS,
input reference level is the crosspoint when in differential strobe mode.
3) Inputs are not recognized as valid until V_REF stabilizes. During the period before V_REF stabilizes, CKE = 0.2 x V_DDQ is recognized as low.
4) The output timing reference voltage level is V_TT.
5) t_RAS.MAX is calculated from the maximum amount of time a DDR2 device can operate without a refresh command which is equal to 9 x t_REFI.
Speed Grade
TABLE 14
Speed Grade Definition Speed Bins for DDR2–533C
DDR2–533C
Unit
Note
QAG Sort Name
–3.7
CAS-RCD-RP latencies
4–4–4
t_CK
Parameter
Symbol
Min.
Max.
—
Clock Frequency
@ CL = 3
t_CK
5
8
ns
1)2)3)4)
@ CL = 4
t_CK
3.75
8
ns
1)2)3)4)
@ CL = 5
t_CK
3.75
8
ns
1)2)3)4)
Row Active Time
t_RAS
45
70000
ns
1)2)3)4)5)
Row Cycle Time
t_RC
60
—
ns
1)2)3)4)
RAS-CAS-Delay
t_RCD
15
—
ns
1)2)3)4)
Row Precharge Time
t_RP
15
—
ns
1)2)3)4)
1) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew
Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode.
2) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS,
input reference level is the crosspoint when in differential strobe mode.
3) Inputs are not recognized as valid until V_REF stabilizes. During the period before V_REF stabilizes, CKE = 0.2 x V_DDQ is recognized as low.
4) The output timing reference voltage level is V_TT.
5) t_RAS.MAX is calculated from the maximum amount of time a DDR2 device can operate without a refresh command which is equal to 9 x t_REFI.
Rev. 1.1, 2007-01
16
08212006-PKYN-2H1B