LC786800E Datasheet, PDF (6/26 Pages) Sanyo Semicon Device – Compressed Audio signal Processor IC with USB host controller

LC786800E
Electrical Characteristics at Ta = -40 to +85C, VDD1 = 3.0V to 3.6V, DVSS = AVSS1 = AVSS2 = XVSS = 0V
Parameter
Symbol
Pin names
Conditions
min
typ
max
Unit
Current drain
High-level input current
Low-level input current
High-level output voltage
IDD1
IIH(1)
IIH(2)
IIL(1)
VOH(1)
VOH(2)
DVDD, AVDD1, AVDD2,
XVDD, VVDD2, VVDD3
RESB, SIFCK, SIFDI, SIFDO,
SIFCE, BUSYB, GP03, GP04,
GP05, GP06, GP07, GP10,
GP11, GP12, GP13, GP14,
JTMS, JTRSTB, JTCK, JTDI
GP30, GP31, GP32, GP33,
GP34, GP35, GP36, GP37,
GP40, GP41, GP42, GP43,
GP44, GP45, GP46, GP47,
GP50, GP51, GP52, GP53
RESB, SIFCK, SIFDI, SIFDO,
SIFCE, BUSYB, GP03, GP04,
GP05, GP06, GP07, GP10,
GP11, GP12, GP13, GP14,
GP30, GP31, GP32, GP33,
GP34, GP35, GP36, GP37,
GP40, GP41, GP42, GP43,
GP44, GP45, GP46, GP47,
GP50, GP51, GP52, GP53,
JTMS, JTRSTB, JTCK, JTDI,
TEST0, TEST1
GP04, GP05, GP06, GP07,
GP12, GP13, GP14, GP30,
GP31, GP32, GP33, GP34,
GP35, GP36, GP37, GP40,
GP41, GP42, GP43, GP44,
GP45, GP46, GP47, GP50,
GP51, GP52, GP53
SIFDI, SIFDO, SIFCE, BUSYB,
GP03, GP10, GP11,
JTDO, JTRTCK
Schmitt,
VIN = 5.50V
Built-in
Pull-down
resistor OFF
Schmitt,
VIN = VDD1
Built-in
Pull-down
resistor OFF
Schmitt,
VIN = 0V
CMOS,
IOH = -2mA
CMOS,
IOH = -4mA
-10.00
VDD1-0.6
VDD1-0.6
85
135 mA
10.00 A
10.00 A
A
V
V
Low-level output voltage
Built-in Pull down resistor
Output off-leakage current
VOL(1)
VOL(2)
RPD
IOFF(1)
GP04, GP05, GP06, GP07,
GP12, GP13, GP14, GP30,
GP31, GP32, GP33, GP34,
GP35, GP36, GP37, GP40,
GP41, GP42, GP43, GP44,
GP45, GP46, GP47, GP50,
GP51, GP52, GP53
SIFDI, SIFDO, SIFCE, BUSYB,
GP03, GP10, GP11,
JTDO, JTRTCK
SIFDO, SIFCE, BUSYB,
GP03, GP04, GP05, GP06,
GP07, GP10, GP11, GP12,
GP13, GP14, GP30, GP31,
GP32, GP33, GP34, GP35,
GP36, GP37, GP40, GP41,
GP42, GP43, GP44, GP45,
GP46, GP47, GP50, GP51,
GP52, GP53
AFILT
CMOS,
IOL = 2mA
CMOS,
IOL = 4mA
Hi-Z Out
0.40
V
0.40
V
50
100
200 k
-10.00
10.00 A
IOFF(2)
SIFDO
Hi-Z Out
-10.00
10.00 A
Charge pump output current IAFILH
AFILT
15.0
A
IAFILL
AFILT
15.0
A
<Note>
 Put a internal pull down resistor or external pull down resistor or external pull up resistor to the SIFDO pin if its
output condition is set to 3-State mode.
No.A2082-6/26