PIC18F46K80-E-PT Datasheet, PDF (5/12 Pages) Microchip Technology – PIC18F66K80 Family Silicon Errata and Data Sheet Clarification

PIC18F66K80
6. Module: IPD and IDD
The IPD and IDD limits do not match the data
sheet. The IPD values, shown in bold in
Section 31.2 “DC Characteristics: Power-
Down and Supply Current PIC18F66K80
Family (Industrial/Extended)” (below), reflect
the updated silicon maximum limits.
All IDD maximum limits will equal 2.8 times the
value listed in the data sheet.
Affected Silicon Revisions
A2 A3 A4
X
.
31.2 DC Characteristics: Power-Down and Supply Current
PIC18F66K80 Family (Industrial/Extended)
PIC18F66K80
(Industrial/Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param
No.
Device
Typ
Max Units
Conditions
Power-Down Current (IPD)⁽¹⁾
PIC18LFXXK80
0.008
7
µA
-40°C
0.013
0.035
0.218
7
µA
9
µA
10 µA
+25°C
+60°C
+85°C
VDD = 1.8V⁽⁴⁾
(Sleep mode)
Regulator Disabled
3
12 µA
±125ºC
PIC18LFXXK80
0.014
8
µA
-40°C
0.034
0.092
0.312
8
µA
9
µA
10 µA
+25°C
+60°C
+85°C
VDD = 3.3V⁽⁴⁾
(Sleep mode)
Regulator Disabled
4
16 µA
±125ºC
PIC18FXXK80
0.2
9
µA
0.23
9
µA
0.32
10 µA
-40°C
+25°C
+60°C
VDD = 3.3V
(Sleep mode)
Regulator Enabled
0.51
11 µA
+85°C
5
18 µA
±125ºC
PIC18FXXK80
0.22
10 µA
-40°C
0.24
10 µA
0.34
11 µA
0.54
12 µA
+25°C
+60°C
+85°C
VDD = 5V⁽⁵⁾
(Sleep mode)
Regulator Enabled
5
20 µA
±125ºC
Legend:
Note 1:
2:
3:
4:
5:
Shading of rows is to assist in readability of the table.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the
part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS, and all features that add delta
current disabled (such as WDT, SOSC oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
For LF devices, RETEN (CONFIG1L<0>) = 1.
For F devices, SRETEN (WDTCON<4>) = 1 and RETEN (CONFIG1L<0>) = 0.
 2011 Microchip Technology Inc.
DS80519D-page 5