PIC18F6393 Datasheet, PDF (3/58 Pages) Microchip Technology – 64/80-Pin High Performance,

PIC18F6393/6493/8393/8493
64/80-Pin High-Performance, Flash Microcontrollers
with LCD Driver, 12-Bit ADC and nanoWatt Technology
LCD Driver Module Features:
• Direct Driving of LCD Panel
• Up to 192 Pixels: Software Selectable
• Programmable LCD Timing module:
- Multiple LCD timing sources available
- Up to four commons: Static, 1/2, 1/3 or
1/4 multiplex
- Static, 1/2 or 1/3 bias configuration
• Can Drive LCD Panel while in Sleep mode for
Low-Power Operation
Power-Managed Modes:
• Run: CPU On, Peripherals On
• Idle: CPU Off, Peripherals On
• Sleep: CPU Off, Peripherals Off
• Run mode Current Down to 14 μA Typical
• Idle mode Currents Down to 5.8 μA Typical
• Sleep mode Currents Down to 0.1 μA Typical
• Timer1 Oscillator: 1.8 μA, 32 kHz, 2V
• Watchdog Timer: 2.1 μA Typical
• Two-Speed Oscillator Start-up
Flexible Oscillator Structure:
• Four Crystal modes:
- LP: Up to 200 kHz
- XT: Up to 4 MHz
- HS: Up to 40 MHz
- HSPLL: 4-10 MHz (16-40 MHz internal)
• 4x Phase Lock Loop (available for crystal and
internal oscillators)
• Two External RC modes, Up to 4 MHz
• Two External Clock modes, Up to 40 MHz
• Internal Oscillator Block:
- Eight selectable frequencies, from 31 kHz to 8 MHz
- Provides a complete range of clock speeds
from 31 kHz to 32 MHz when used with PLL
- User-tunable to compensate for frequency drift
• Secondary Oscillator Using Timer1 at 32 kHz
• Fail-Safe Clock Monitor:
- Allows for safe shutdown of device if primary
or secondary clock fails
Peripheral Highlights:
• 12-Bit, Up to 12-Channel Analog-to-Digital (A/D)
Converter module:
- Auto-acquisition capability
- Conversion available during Sleep
• High-Current Sink/Source 25 mA/25 mA
• Four External Interrupts
• Four Input Change Interrupts
• Four 8-Bit/16-Bit Timer/Counter modules
• Real-Time Clock (RTC) Software module:
- Configurable 24-hour clock, calendar, automatic
100-year or 12,800-year, day-of-week calculator
- Uses Timer1
• Up to Two Capture/Compare/PWM (CCP) modules
• Master Synchronous Serial Port (MSSP) module
Supporting Three-Wire SPI (all four modes) and
I²C™ Master and Slave modes
• Addressable USART module:
- Supports RS-485 and RS-232
• Enhanced Addressable USART module:
- Supports RS-485, RS-232 and LIN 1.2
- Auto-wake-up on Start bit
- Auto-Baud Detect
• Dual Analog Comparators with Input Multiplexing
Special Microcontroller Features:
• C Compiler Optimized Architecture:
- Optional extended instruction set designed to
optimize re-entrant code
• 1000 Erase/Write Cycle Flash Program Memory
Typical
• Flash Retention: 100 Years Typical
• Priority Levels for Interrupts
• 8 x 8 Single-Cycle Hardware Multiplier
• Extended Watchdog Timer (WDT):
- Programmable period from 4 ms to 132s
- 2% stability over VDD and temperature
• In-Circuit Serial Programming™ (ICSP™) via Two Pins
• In-Circuit Debug (ICD) via Two Pins
• Wide Operating Voltage Range: 2.0V to 5.5V
Note:
This document is supplemented by the
“PIC18F6390/6490/8390/8490 Data Sheet”
(DS39629). See Section 1.0 “Device
Overview”.
© 2007 Microchip Technology Inc.
Preliminary
DS39896A-page 1