24AA64_02 Datasheet, PDF (3/24 Pages) Microchip Technology – 64K I2C™ Serial EEPROM

24AA64/24LC64
1.2 AC Characteristics
AC CHARACTERISTICS
VCC = +1.8V to +5.5V
Industrial (I):
TAMB = -40°C to +85°C
Automotive (E): TAMB = -40°C to +125°C
Param.
No.
Sym
Characteristic
Min
Max Units
Conditions
1
FCLK Clock frequency
—
400 kHz 2.5V ≤ VCC ≤ 5.5V
—
100
1.8V ≤ VCC < 2.5V (24AA64)
2
THIGH Clock high time
600
4000
—
ns 2.5V ≤ VCC ≤ 5.5V
—
1.8V ≤ VCC < 2.5V (24AA64)
3
TLOW Clock low time
1300
4700
—
ns 2.5V ≤ VCC ≤ 5.5V
—
1.8V ≤ VCC < 2.5V (24AA64)
4
TR SDA and SCL rise time
(Note 1)
—
300
ns 2.5V ≤ VCC ≤ 5.5V
—
1000
1.8V ≤ VCC < 2.5V (24AA64)
5
TF SDA and SCL fall time
—
300
ns (Note 1)
6 THD:STA START condition hold time
600
4000
—
ns 2.5V ≤ VCC ≤ 5.5V
—
1.8V ≤ VCC < 2.5V (24AA64)
7 TSU:STA START condition setup time
600
4700
—
ns 2.5V ≤ VCC ≤ 5.5V
—
1.8V ≤ VCC < 2.5V (24AA64)
8 THD:DAT Data input hold time
0
—
ns (Note 2)
9 TSU:DAT Data input setup time
100
—
ns 2.5V ≤ VCC ≤ 5.5V
250
—
1.8V ≤ VCC < 2.5V (24AA64)
10 TSU:STO STOP condition setup time
600
4000
—
ns 2.5V ≤ VCC ≤ 5.5V
—
1.8V ≤ VCC < 2.5V (24AA64)
11
TAA Output valid from clock
(Note 2)
—
900
ns 2.5V ≤ VCC ≤ 5.5V
—
3500
1.8V ≤ VCC < 2.5V (24AA64)
12
TBUF Bus free time: Time the bus
1300
must be free before a new
4700
transmission can start
—
ns 2.5V ≤ VCC ≤ 5.5V
—
1.8V ≤ VCC < 2.5V (24AA64)
13
TOF Output fall time from VIH min- 20+0.1CB 250
ns 2.5V ≤ VCC ≤ 5.5V
imum to VIL maximum
—
250
1.8V ≤ VCC ≤ 2.5V (24AA64)
14
TSP Input filter spike suppression
—
(SDA and SCL pins)
50
ns (Notes 1 and 3)
15
TWC Write cycle time (byte or
page)
—
5
ms —
16
— Endurance
1M
— cycles 25°C, VCC = 5.0V, Block Mode
(Note 4)
Note 1: Not 100% tested. CB = total capacitance of one bus line in pF.
2: As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region
(minimum 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions.
3: The combined TSP and VHYS specifications are due to new Schmitt Trigger inputs which provide improved
noise spike suppression. This eliminates the need for a TI specification for standard operation.
4: This parameter is not tested but ensured by characterization. For endurance estimates in a specific appli-
cation, please consult the Total Endurance Model which can be obtained on Microchip’s website:
www.microchip.com.
 2002 Microchip Technology Inc.
DS21189F-page 3