MAX8893A Datasheet, PDF (9/50 Pages) Maxim Integrated Products – μPMICs for Multimedia Application Processors in a 3.0mm x 2.5mm WLP

µPMICs for Multimedia Application Processors
in a 3.0mm x 2.5mm WLP
ELECTRICAL CHARACTERISTICS (continued)
(Typical Operating Circuit, VIN = 3.7V, CBATT = CIN1 = CIN2 = 2.2FF, CREFBP = 0.1FF, TA = -40NC to +85NC, unless otherwise noted.
Typical values are at TA = +25NC.) (Notes 3, 4)
PARAMETER
CONDITIONS
MIN TYP MAX UNIT
Load Regulation
1mA < ILOAD < 150mA
VENLDO5 = VBATT
25
mV
Power-Supply Rejection
DVLDO5/DVIN2
Output Noise Voltage
Output Capacitor for Stable
Operation (Note 6)
Ground Current
Startup Time from Shutdown
Shutdown Output Resistance
USB HIGH-SPEED SWITCH
Operating Power-Supply Range
Supply Current
Fault Protection Trip Threshold
(VFP)
On-Resistance (RON)
On-Resistance Match Between
Channels (DRON)
On-Resistance Flatness (RFLAT)
Off-Leakage Current
(ICOM_(OFF))
10Hz to 10kHz, CLDO5 = 1FF, ILOAD = 30mA
100Hz to 100kHz, CLDO5 = 1FF, ILOAD = 30mA
0mA < ILOAD < 200mA
0mA < ILOAD < 150mA
ILOAD = 500FA
CLDO5 = 2.2FF, ILOAD = 200mA
LDO5_ADEN = 1, VENLDO5 = 0V
VENUSB = 0V, VCB = 0V or VBATT
VBATT = 3.0V
VBATT = 5.5V
COM­_ only, TA = +25NC
VCOM_ = 0V to VBATT
VCOM_ = 3.6V, VBATT = 3.0V
VBATT = 3.0V, VCOM_ = 2V (Note 7)
VBATT = 3.0V, VCOM_ = 0V to VIN (Note 8)
VBATT = 4.5V, VCOM_ = 0V or 4.5V,
VNO_, VNC_ = 4.5V or 0V
VBATT = 5.5V, VCOM_ = 0V or 5.5V,
VNO_, VNC_ with 50FA sink current to AGND
75
45
1.4
2.2
0.7
1.0
21
40
300
dB
FVRMS
FF
FA
Fs
I
2.7
5.5
V
0.6
FA
3
VIN + VIN + VIN +
0.6
0.8
1.0
V
5
10
I
5.5
0.1
1
I
0.1
I
-250
+250 nA
180
FA
On-Leakage Current (ICOM_(ON))
VBATT = 5.5V, VCOM_ = 0V or 5.5V,
VNO_, and VNC_ are unconnected
USB HIGH-SPEED SWITCH AC PERFORMANCE
-250
+250 nA
On-Channel -3dB Bandwidth
(BW)
RL = RS = 50I, signal = 0dBm
950
MHz
Off-Isolation (VISO)
VNO_, VNC_ = 0dBm,
RL = RS = 50I,
Figure 1
Crosstalk (VCT)
VNO_, VNC_ = 0dBm,
RL = RS = 50I,
Figure 1 (Note 9)
USB HIGH-SPEED SWITCH LOGIC INPUT (CB)
Input Logic-High (VIH)
Input Logic-Low (VIL)
Input Leakage Current (IIN)
f = 10MHz
f = 250MHz
f = 500MHz
f = 10MHz
f = 250MHz
f = 500MHz
-48
-20
dB
-17
-73
-54
dB
-33
1.4
-250
V
0.4
V
+250 nA
_______________________________________________________________________________________   9