MAX1358B Datasheet, PDF (51/71 Pages) Maxim Integrated Products – 16-Bit, Data-Acquisition System with ADC, DACs, UPIOs, RTC, Voltage Monitors, and Temp Sensor

16-Bit, Data-Acquisition System with ADC, DACs,
UPIOs, RTC, Voltage Monitors, and Temp Sensor
UPIO4_CTRL Register (Power-On State: 0000 1000)
MSB
UP4MD3
UP4MD2
UP4MD1
UP4MD0
The UPIO4_CTRL register configures the UPIO4 pin
functionality.
UP4MD<3:0>: UPIO4-mode selection bits. These bits
configure the mode for the UPIO4 pin. See Table 16 for
a detailed description. The power-on default is 0 hex.
PUP4: Pullup UPIO4 control bit. Set PUP4 = 1 to enable
a weak pullup resistor on the UPIO4 pin, and set PUP4
= 0 to disable it. The pullup resistor is connected to
either DV_DD or CPOUT as programmed by the SV4 bit.
The pullup is enabled only when UPIO4 is configured as
an input. Open-drain behavior can be simulated at
UPIO4 by setting the mode to GPO with LL4 = 0 and by
changing the mode to GPI with PUP4 = 0, allowing
external high pullup. The power-on default is 1.
SV4: Supply-voltage UPIO4 selection bit. Set SV4 = 0
to select DV_DD as the supply voltage for the UPIO4 pin,
and set SV4 = 1 to select CPOUT as the supply volt-
age. The selected supply voltage applies to all modes
for the UPIO4 pin. The power-on default is 0.
LSB
PUP4
SV4
ALH4
LL4
ALH4: Active logic-level assertion high UPIO4 bit. Set
ALH4 = 0 to define the input or output assertion level
for UPIO4 as low except when in GPI and GPO modes.
Set ALH4 = 1 to define the input or output assertion
level as high. For example, asserting ALH4 defines the
UPIO4 output signal as ALARM, while deasserting
ALH4 defines it as ALARM. Similarly, asserting ALH4
defines the UPIO4 input signal as WU, while deassert-
ing ALH4 defines it as WU. The power-on default is 0.
LL4: Logic-level UPIO4 bit. When UPIO4 is configured
as GPO, LL4 = 0 sets the output to a logic-low and LL4
= 1 sets the output to a logic-high. A read of LL4
returns the voltage level at the UPIO4 pin at the time of
the read, regardless of how it is programmed. The
power-on default is 0.
UPIO3_CTRL Register (Power-On State: 0000 1000)
MSB
UP3MD3
UP3MD2
UP3MD1
UP3MD0
The UPIO3_CTRL register configures the UPIO3 pin
functionality.
UP3MD<3:0>: UPIO3-mode selection bits. These bits
configure the mode for the UPIO3 pin. See Table 16 for
a detailed description. The power-on default is 0 hex.
PUP3: Pullup UPIO3 control bit. Set PUP3 = 1 to enable
a weak pullup resistor on the UPIO3 pin, and set PUP3
= 0 to disable it. The pullup resistor is connected to
either DV_DD or CPOUT as programmed by the SV3 bit.
The pullup is enabled only when UPIO3 is configured as
an input. Open-drain behavior can be simulated at
UPIO3 by setting the mode to GPO with LL3 = 0 and by
changing the mode to GPI with PUP3 = 0, allowing
external high pullup. The power-on default is 1.
SV3: Supply-voltage UPIO3 selection bit. Set SV3 = 0
to select DV_DD as the supply voltage for the UPIO3 pin,
and set SV3 = 1 to select CPOUT as the supply volt-
age. The selected supply voltage applies to all modes
for the UPIO3 pin. The power-on default is 0.
LSB
PUP3
SV3
ALH3
LL3
ALH3: Active logic-level assertion high UPIO3 bit. Set
ALH3 = 0 to define the input or output assertion level
for UPIO3 as low except when in GPI and GPO modes.
Set ALH3 = 1 to define the input or output assertion
level as high. For example, asserting ALH3 defines the
UPIO3 output signal as ALARM, while deasserting
ALH3 defines it as ALARM. Similarly, asserting ALH3
defines the UPIO3 input signal as WU, while deassert-
ing ALH3 defines it as WU. The power-on default is 0.
LL3: Logic-level UPIO3 bit. When UPIO3 is configured
as GPO, LL3 = 0 sets the output to a logic-low and LL3
= 1 sets the output to a logic-high. A read of LL3
returns the voltage level at the UPIO3 pin at the time of
the read, regardless of how it is programmed. The
power-on default is 0.
______________________________________________________________________________________ 51