MAX1438B Datasheet, PDF (2/21 Pages) Maxim Integrated Products – Octal, 12-Bit, 64Msps, 1.8V ADC with Serial LVDS Outputs

Octal, 12-Bit, 64Msps, 1.8V ADC
with Serial LVDS Outputs
ABSOLUTE MAXIMUM RATINGS
AVDD to GND........................................................-0.3V to +2.0V
CVDD to GND........................................................-0.3V to +3.6V
OVDD to GND .......................................................-0.3V to +2.0V
IN_P, IN_N to GND .................................-0.3V to (V_AVDD + 0.3V)
CLK to GND ...........................................-0.3V to (V_CVDD + 0.3V)
OUT_P, OUT_N, FRAME_,
CLKOUT_ to GND ..............................-0.3V to (V_OVDD + 0.3V)
DT, SLVS/LVDS, LVDSTEST, PLL_, STBY
REFIO, REFADJ, CMOUT to GND......-0.3V to (V_AVDD + 0.3V)
Continuous Power Dissipation (T_A = +70°C)
68-Pin Thin QFN, 10mm x 10mm x 0.8mm
(derate 70mW/°C above +70°C) ................................4000mW
Operating Temperature Range ...........................-40°C to +85°C
Maximum Junction Temperature .....................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V_AVDD = 1.8V, V_OVDD = 1.8V, V_CVDD = 1.8V, V_GND = 0V, external V_REFIO = 1.24V, C_REFIO to GND = 0.1µF || 1.0µF, C_REFP to GND =
10µF, C_REFN to GND = 10µF, f_CLK = 64MHz (50% duty cycle), DT = 0, T_A = T_MIN to T_MAX, unless otherwise noted. Typical values are
at T_A = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX UNITS
DC ACCURACY (Note 2)
Resolution
N
12
Bits
Integral Nonlinearity
INL
±0.4
±2.5
LSB
Differential Nonlinearity
DNL No missing codes over temperature
±0.25
±1
LSB
Offset Error
±0.5
%FS
Gain Error
-3
±0.5
+2
%FS
ANALOG INPUTS (IN_P, IN_N)
Input Differential Range
Common-Mode Voltage Range
V_ID
V_CMO
Differential input
1.4
0.76
V_P-P
V
Common-Mode Voltage Range
Tolerance
(Note 3)
±50
mV
Differential Input Impedance
Differential Input Capacitance
CONVERSION RATE
R_IN Switched capacitor load
C_IN
2
kΩ
12.5
pF
Maximum Conversion Rate
Minimum Conversion Rate
Data Latency
f_SMAX
f_SMIN
64
4.0
6.5
MHz
MHz
Cycles
DYNAMIC CHARACTERISTICS (Differential Inputs, 4096-Point FFT) (Note 2)
Signal-to-Noise Ratio
Signal-to-Noise and Distortion
Effective Number of Bits
Spurious-Free Dynamic Range
SNR
SINAD
ENOB
SFDR
f_IN = 5.3MHz at -0.5dBFS
f_IN = 20MHz at -0.5dBFS
f_IN = 5.3MHz at -0.5dBFS
f_IN = 20MHz at -0.5dBFS
f_IN = 5.3MHz at -0.5dBFS
f_IN = 20MHz at -0.5dBFS
f_IN = 5.3MHz at -0.5dBFS
f_IN = 20MHz at -0.5dBFS
69.9
dB
67
69.6
69.8
dB
67
69.6
11.4
Bits
10.8
11.4
94
dBc
79
93
2 _______________________________________________________________________________________