LTC3829_15 Datasheet, PDF (18/40 Pages) Linear Technology – 3-Phase, Single Output Synchronous Step-Down DC/DC Controller with Diffamp

LTC3829
APPLICATIONS INFORMATION
The NTC resistor has a negative temperature coefficient,
meaning its value decreases as temperature rises. The
V_ITEMP voltage, therefore, decreases as temperature in-
creases and in turn, the V_{SENSEMAX(ADJ)} will increase to
compensate the DCR temperature coefficient. The NTC
resistor, however, is nonlinear and the user can linear-
ize its value by building a resistor network with regular
resistors. Consult the NTC manufacture data sheets for
detailed information.
Another use for the ITEMP pins, in addition to NTC com-
pensated DCR sensing, is adjusting V_SENSE(MAX) to values
between the nominal values of 30mV, 50mV and 75mV for
a more precise current limit. This is done by applying a
voltage less than 0.5V to the ITEMP pin. V_SENSE(MAX) will
be varied per the previous equation and the same duty cycle
limitations will apply. The current limit can be adjusted using
this method either with a sense resistor or DCR sensing.
Calculate the values for R_P and R_S. A simple method is to
graph the following R_S versus R_P equations with R_S on
the y-axis and R_P on the x-axis.
R_S = R_ITEMP25C – R_NTC25C || R_P
R_S = R_ITEMP100C – R_NTC100C || R_P
Next, find the value of R_P that satisfies both equations
which will be the point where the curves intersect. Once
R_P is known, solve for R_S.
The resistance of the NTC thermistor can be obtained
from the vendor’s data sheet either in the form of graphs,
tabulated data or formulas. The approximate value for the
NTC thermistor for a given temperature can be calculated
from the following equation:
R
=
R_O

•exp_
B

•_
1
T+ 273
–
T_O
1^
+ 273


NTC Compensated DCR Sensing
For DCR sensing applications where a more accurate
current limit is required, a network consisting of an NTC
thermistor placed from the ITEMP pin to ground will
provide correction of the current limit over temperature.
Figure 2b shows this network. Resistors R_S and R_P will
linearize the impedance the ITEMP pin sees. To implement
NTC compensated DCR sensing, design the DCR sense
filter network per the same procedure mentioned in the
previous selection, except calculate the divider components
using the room temperature value of the DCR. For a single
output rail operating from one phase:
1. Set the ITEMP pin resistance to 50k at 25°C. With
10µA flowing out of the ITEMP pin, the voltage on the
ITEMP pin will be 0.5V at room temperature. Current
limit correction will occur for inductor temperatures
greater than 25°C.
where:
R = resistance at temperature T, which is in degrees C
R_O = resistance at temperature T_O, typically 25°C
B = B-constant of the thermistor.
Figure 5 shows a typical resistance curve for a 100k
thermistor and the ITEMP pin network over temperature.
Starting values for the NTC compensation network are
listed below:
• NTC R_O = 100k
• R_S = 20k
• R_P = 50k
But, the final values should be calculated using the above
equations and checked at 25°C and 100°C.
2. Calculate the ITEMP pin resistance and the maximum
inductor temperature which is typically 100°C. Use the
equations:
R_ITEMP100C
=
V_ITEMP100C
10μA
V_ITEMP100C
=
0.5V
–
1.3I^MAX
•DCR(MAX)
•R2/(R1+R2) •(100°C–
V_SENSE(MAX)
25°C)
•0.4/100
3829fc
18
For more information www.linear.com/LTC3829