LTC3829_15 Datasheet, PDF (11/40 Pages) Linear Technology – 3-Phase, Single Output Synchronous Step-Down DC/DC Controller with Diffamp

LTC3829
OPERATION (Refer to Functional Diagram)
Main Control Loop
The LTC3829 uses a constant frequency, current mode
step-down architecture. During normal operation, each
top MOSFET is turned on each cycle when the oscillator
sets the RS latch, and turned off when the main current
comparator, I_CMP , resets each RS latch. The peak inductor
current at which I_CMP resets the RS latch is controlled by
the voltage on the I_TH pin, which is the output of the er-
ror amplifier, EA. The remote sense amplifier (DIFFAMP)
produces a signal equal to the differential voltage sensed
across the output capacitor and re-references it to the lo-
cal IC ground reference. The V_FB pin receives a portion of
this feedback signal and compares it to the internal 0.6V
reference. When the load current increases, it causes a
slight decrease in the V_FB pin voltage relative to the 0.6V
reference, which in turn causes the I_TH voltage to increase
until each inductor’s average current equals one-third of
the new load current (assuming all three current sensing
resistors are equal). After each top MOSFET has turned off,
the bottom MOSFET is turned on until either the inductor
current starts to reverse, as indicated by the reverse cur-
rent comparator, I_REV , or the beginning of the next cycle.
The main control loop is shut down by pulling the RUN
pin low. Releasing RUN allows an internal 1.0µA current
source to pull up the RUN pin. When the RUN pin reaches
1.22V, the main control loop is enabled and the IC is
powered up. When the RUN pin is low, all functions are
kept in a controlled state.
INTV_CC/EXTV_CC Power
Power for the top and bottom MOSFET drivers and most
other internal circuitry is derived from the INTV_CC pin.
When the EXTV_CC pin is left open or tied to a voltage less
than 4.7V, an internal 5V linear regulator supplies INTV_CC
power from V_IN. If EXTV_CC is taken above 4.7V, the 5V
regulator is turned off and an internal switch is turned on
connecting EXTV_CC. Using the EXTV_CC pin allows the INTV_CC
power to be derived from a high efficiency external source
such as a switching regulator output. Each top MOSFET
driver is biased from the floating bootstrap capacitor, C_B,
which normally recharges during each off cycle through
an external diode when the top MOSFET turns off. If the
input voltage, V_IN, decreases to a voltage close to V_OUT ,
the loop may enter dropout and attempt to turn on the
top MOSFET continuously. The dropout detector detects
this and forces the top MOSFET off for about one-twelfth
of the clock period plus 100ns every third cycle to allow
C_B to recharge. However, it is recommended that a load
be present or the IC operates at low frequency during the
dropout transition to ensure C_B is recharged.
Shutdown and Start-Up (RUN and TK/SS Pins)
The LTC3829 can be shut down using the RUN pin. Pulling
the RUN pin below 1.22V shuts down the main control loop
for the controller and most internal circuits, including the
INTV_CC regulator. Releasing the RUN pin allows an internal
1.0µA current to pull up the pin and enable the controller.
Alternatively, the RUN pin may be externally pulled up or
driven directly by logic. Be careful not to exceed the ab-
solute maximum rating of 6V on this pin. The start-up of
the controller’s output voltage, V_OUT , is controlled by the
voltage on the TK/SS pin. When the voltage on the TK/SS
pin is less than the 0.6V internal reference, the LTC3829
regulates the V_FB voltage to the TK/SS pin voltage instead
of the 0.6V reference. This allows the TK/SS pin to be used
to program a soft-start by connecting an external capacitor
from the TK/SS pin to SGND. An internal 1.25µA pull-up
current charges this capacitor, creating a voltage ramp on
the TK/SS pin. As the TK/SS voltage rises linearly from
0V to 0.6V (and beyond), the output voltage, V_OUT , rises
smoothly from zero to its final value. Alternatively, the TK/
SS pin can be used to cause the start-up of V_OUT to track
that of another supply. Typically, this requires connect-
ing to the TK/SS pin an external resistor divider from the
other supply to ground (see the Applications Information
section). When the RUN pin is pulled low to disable the
controller, or when INTV_CC drops below its undervoltage
lockout threshold of 3.3V, the TK/SS pin is pulled low
by an internal MOSFET. When in undervoltage lockout,
all phases of the controller are disabled and the external
MOSFETs are held off.
For more information www.linear.com/LTC3829
3829fc
11