2000 Datasheet, PDF (15/24 Pages) Make-Ps – Single, Dual, Triple Output DC/DC Converter

15 | Keysight | InfiniiVision 2000 X-Series Oscilloscopes - Data Sheet
Performance Characteristics
Specification overview
Bandwidth ¹ (–3 dB)
Calculated rise time (10 to 90%)
Input channels
Maximum sample rate ¹
Maximum memory depth
Display size and type
Waveform update rate
Vertical system analog channels
Input coupling
Input sensitivity range
Input impedance
Vertical resolution
Dynamic range
Maximum input voltage
DSOX
MSOX
DC vertical accuracy
DC vertical gain accuracy ¹
DC vertical offset accuracy
Channel-to-channel isolation
Position/offset range
Hardware bandwidth limits
Horizontal system analog channels
1 MΩ
Time base range
Horizontal resolution
Time base accuracy ¹
Time base delay time range
Channel-to-channel deskew range
Δ Time accuracy (using cursors)
Pre-trigger
Post-trigger
2002A
2004A
2012A
2014A
2022A
2024A
70 MHz
100 MHz
200 MHz
≤ 5 ns
≤ 3.5 ns
≤ 1.75 ns
2
4
2
4
2
4
2+8
4+8
2+8
4+8
2+8
4+8
2 GSa/s half-channel interleaved, 1 GSa/s per channel
100 kpts per channel (standard), 1 Mpt per channel (optional with DSOX2MEMUP)
8.5-inch WVGA with 64 levels of intensity grading
50,000 waveforms per second
AC, DC
1 mV/div to 5 V/div ²
1 MΩ ± 2% (11 pF)
8 bits (measurement resolution is 12 bits with averaging)
± 8 divisions from center screen
300 Vrms, 400 Vpk; transient overvoltage 1.6 kVpk
With N2862B or N2863B 10:1 probe: 300 Vrms
Frequency de-rating (assumes sine wave input): 400 Vpk until 40 kHz. Then de-rates at
20 db/dec until 6 Vpk
± [DC vertical gain accuracy + DC vertical offset accuracy + 0.25% full scale] ²
± 3% full scale (≥ 10 mV/div); ± 4% full scale (< 10 mV/div) ²
± 0.1 div ± 2mV ± 1% of offset setting
≥ 40 dB from DC to maximum specified bandwidth of each model
1 mV to 200 mV/div: ± 2 V, > 200 mV to 5 V/div: ± 50 V
Approximately 20 MHz (selectable)
2002A
2004A
2012A
2014A
2022A
2024A
5 ns/div to 50 s/div
2 ns/div to 50 s/div
2.5 ps
25 ppm ± 5 ppm per year (aging)
Greater of 1 screen width or 200 μs (400 μs in interleaving mode)
1 s to 500 s
± 100 ns
± (time base accuracy ¹ reading) ± (0.0016 ¹ screen width) ± 100 ps
1.  Denotes warranted specifications, all others are typical. Specifications are valid after a 30-minute warm-up period and from ± 10 °C firmware calibration
temperature.
2.  1 mV/div and 2 mV/div is a magnification of 4 mV/div setting. For vertical accuracy calculations, use full scale of 32 mV for 1 mV/div and 2 mV/div sensitivity
setting.