ISL6564 Datasheet, PDF (8/27 Pages) Intersil Corporation – Multi-Phase PWM Controller with Linear 6-bit DAC Capable of Precision rDS(ON) or DCR Differential Current Sensing

ISL6564
Absolute Maximum Ratings
Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+7V
Input and Output Voltage (except OVP). . GND -0.3V to V_CC + 0.3V
OVP Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+15V
ESD (Human body model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>4kV
ESD (Machine model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>300V
ESD (Charged device model) . . . . . . . . . . . . . . . . . . . . . . . . . .>2kV
Thermal Information
Thermal Resistance
θ_JA (°C/W) θ_JC (°C/W)
QFN Package (Notes 1, 2). . . . . . . . . .
32
3.5
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . - 65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C
Operating Conditions
Supply Voltage, VCC (5V bias mode, Note 2) . . . . . . . . . . +5V ±5%
Ambient Temperature (ISL6564CR, ISL6564CRZ) . . . . 0°C to 70°C
Ambient Temperature (ISL6564IR, ISL6564IRZ) . . . . .-40°C to 85°C
CAUTION: Stress above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational section of this specification is not implied.
NOTES:
1. θ_JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
Tech Brief TB379.
2. For θ_JC, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications Operating Conditions: VCC = 5V or ICC < 25mA (Note 3).
Unless Otherwise Specified.
PARAMETER
TEST CONDITIONS
MIN TYP MAX UNITS
VCC SUPPLY CURRENT
Nominal Supply
VCC = 5VDC; EN = 5VDC; R_T = 100kΩ,
ISEN1 = ISEN2 = ISEN3 = ISEN4 = -70µA
-
14 18 mA
Shutdown Supply
SHUNT REGULATOR
VCC = 5VDC; EN = 0VDC; R_T = 100 kΩ
-
10 14 mA
VCC Voltage
VCC Sink Current
POWER-ON RESET AND ENABLE
VCC tied to 12VDC thru 300Ω resistor, R_T = 100kΩ
VCC tied to 12VDC thru 300Ω resistor, R_T = 100kΩ
5
5.9 6.5
V
-
-
25 mA
POR Threshold
VCC Rising
4.20 4.31 4.50 V
VCC Falling
3.60 3.80 4.00 V
ENABLE Threshold
EN Rising
1.26 1.29 1.32 V
Hysteresis
110 125 135 mV
Fault Reset
1.12 1.16 1.20 V
ENLL Input Logic Low Level
-
-
0.4
V
ENLL input Logic High Level
0.8
-
-
V
ENLL Leakage Current
ENLL = 5V
-
-
1
µA
REFERENCE VOLTAGE AND DAC
System Accuracy (VID = 1.V-1.3V)
(Note 3)
-0.5
-
0.5 %VID
System Accuracy (VID = 0.525V-0.9875V) (Note 3)
-0.9
-
0.9 %VID
VID Pull Up
-55 -45 -35 µA
VID Input Low Level
-
-
0.4
V
VID Input High Level
0.8
-
-
V
DAC Source/Sink Current
VID = 010100
-200 - 200 µA
VID Input Voltage when Floated
1.0 1.15 1.30 V
REF Source/Sink Current
-50
-
50
µA
8
FN9156.2
December 27, 2004