X80130 Datasheet, PDF (3/18 Pages) Intersil Corporation – Voltage Supervisor/Sequencer Triple Programmable Time Delay with Local/Remote Voltage Monitors

X80130, X80131, X80132, X80133, X80134
Absolute Maximum Ratings
Temperature under bias . . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
ViMON pins (i = 1, 3, 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V
ViGDO pins (i = 1, 3, 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V
RESET pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V
SDA, SCL, WP, A0, A1 pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V
MR pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V
V_P pin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14V
D.C. output current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA
Lead temperature (soldering, 10 seconds) . . . . . . . . . . . . . . . 300°C
Recommended Operating Conditions
Temperature Range (Industrial) . . . . . . . . . . . . . . . . . . -40°C to 85°C
V_CC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5 to 5.5V
CAUTION: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional
operation of the device (at these or any other conditions above those listed in the operational sections of this specification) is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
Electrical Specifications (Standard Settings) Over the recommended operating conditions unless otherwise specified.
SYMBOL
PARAMETER
DC CHARACTERISTICS
TEST CONDITIONS
MIN
TYP
MAX
V_CC
I_CC
V_P
I_P (Note 3)
I_LI
I_LO
V_IL
V_IH
V_OL
C_OUT
(Note 1)
V_TRIP1
Supply Operating Range
Supply Current
EEPROM programming voltage
Programming Current
Input Leakage Current (MR)
Output Leakage Current
(V1GDO, V3GDO, V4GDO, RESET)
Input LOW Voltage (MR)
Input HIGH Voltage (MR)
Output LOW Voltage
(RESET, V1GDO, V3GDO, V4GDO)
Output Capacitance
(RESET, V1GDO, V3GDO, V4GDO)
V1MON Trip Point Voltage (Range)
X80130
f_SCL = 0kHz
V_IL = GND to V_CC
I_OL = 4.0mA
V_OUT = 0V
4.5
5.5
1.0
2.5
9
12
10
15
15
-0.5
V_CC x 0.7
V_CC x 0.3
5.5
0.4
8
2.20
4.70
4.45
4.50
4.55
X80131
4.45
4.50
4.55
X80132
2.95
3.00
3.05
X80133
2.95
3.00
3.05
X80134
2.95
3.00
3.05
V_TRIP3
V3MON Trip Point Voltage
X80130
0.85
3.5
2.95
3.00
3.05
X80131
2.20
2.25
2.30
X80132
2.20
2.25
2.30
X80133
2.20
2.25
2.30
X80134
0.85
0.90
0.95
UNIT
V
mA
V
mA
µA
µA
V
V
V
pF
V
V
V
V
V
V
V
V
V
V
V
V
3
FN8152.0
January 20, 2005