80C88_08 Datasheet, PDF (16/38 Pages) Intersil Corporation – CMOS 8-/16-Bit Microprocessor

80C88
Absolute Maximum Ratings
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8.0V
Input, Output or I/O Voltage . . . . . . . . . . . GND - 0.5V to V_CC + 0.5V
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1
Operating Conditions
Operating Voltage Range. . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V
M80C88-2 Only . . . . . . . . . . . . . . . . . . . . . . . . . +4.75V to +5.25V
Operating Temperature Range
C80C88/-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C
I80C88/-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
M80C88 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55°C to +125°C
Thermal Information
Thermal Resistance (Typical) . . . . . . . . . . . . . . . . . . . . . .θ_JA (^oC/W)
PDIP Package* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
CERDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Maximum Junction Temperature
Ceramic Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +175°C
Plastic Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Storage Temperature Range . . . . . . . . . . . . . . . . . -65°C to +150°C
Pb-free reflow profile. . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
*Pb-free PDIPs can be used for through hole wave solder processing
only. They are not intended for use in Reflow solder processing applica-
tions.
Die Characteristics
Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9750 Gates
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
Electrical Specifications
V_CC = 5.0V, ±10%; T_A = 0°C to +70°C (C80C88, C80C88-2)
V_CC = 5.0V, ±10%; T_A = -40°C to +85°C (l80C88, I80C88-2)
V_CC = 5.0V, ±10%; T_A = -55°C to +125°C (M80C88)
SYMBOL
PARAMETER
TEST CONDITION
MIN
MAX
UNITS
V_lH
Logical One Input Voltage
C80C88, I80C88 (Note 4)
M80C88 (Note 4)
2.0
-
V
2.2
V
V_IL
VIHC
VILC
Logical Zero Input Voltage
CLK Logical One Input Voltage
CLK Logical Zero Input Voltage
-
0.8
V
V_CC - 0.8
-
V
-
0.8
V
V_OH
Output High Voltage
V_OL
Output Low Voltage
I_I
Input Leakage Current
lOH = -2.5mA
3.0
-
V
lOH = -100µA
lOL = +2.5mA
V_CC - 0.4
V
-
0.4
V
V_IN = 0V or V_CC
Pins 17 thru 19, 21 thru 23 and 33
-1.0
1.0
µA
lBHH
lBHL
I_O
ICCSB
ICCOP
Input Current-Bus Hold High
Input Current-Bus Hold Low
Output Leakage Current
Standby Power Supply Current
Operating Power Supply Current
V_IN = - 3.0V (Note 1)
V_IN = - 0.8V (Note 2)
V_OUT = 0V (Note 5)
V_CC = 5.5V (Note 3)
FREQ = Max, V_IN = V_CC or GND,
Outputs Open
-40
-400
µA
40
400
µA
-
-10.0
µA
-
500
µA
-
10
mA/MHz
NOTES:
1. lBHH should be measured after raising V_IN to V_CC and then lowering to 3.0V on the following pins 2 thru16, 26 thru 32, 34 thru 39.
2. IBHL should be measured after lowering V_IN to GND and then raising to 0.8V on the following pins: 2 thru16, 35 thru 39.
3. lCCSB tested during clock high time after HALT instruction executed. V_IN = V_CC or GND, V_CC = 5.5V, Outputs unloaded.
4. MN/MX is a strap option and should be held to V_CC or GND.
5. IO should be measured by putting the pin in a high impedance state and then driving V_OUT to GND on the following pins: 26-29 and 32.
Capacitance T_A = +25°C
SYMBOL
PARAMETER
C_IN
C_OUT
CI/O
Input Capacitance
Output Capacitance
I/O Capacitance
TEST CONDITIONS
FREQ = 1MHz. All measurements are referenced to device GND
FREQ = 1MHz. All measurements are referenced to device GND
FREQ = 1MHz. All measurements are referenced to device GND
TYPICAL
25
25
25
UNITS
pF
pF
pF
16
FN2949.4
February 22, 2008