ICS932SQ420DGLF Datasheet, PDF (9/27 Pages) Integrated Device Technology – PCIE GEN 2/3 & QPI CLOCK FOR ROMLEY-BASED SERVERS

932SQ420D
PCIE GEN 2/3 & QPI CLOCK FOR ROMLEY-BASED SERVERS
Electrical Characteristics - Absolute Maximum Ratings
PARAMETER
SYMBOL
CONDITIONS
MIN
3.3V Core Supply Voltage VDDA
3.3V Logic Supply Voltage VDD
Input Low Voltage
V_IL
GND-0.5
Input High Voltage
V_IH
Except for SMBus interface
Input High Voltage
V_IHSMB
SMBus clock and data pins
Storage Temperature
Ts
-65
Junction Temperature
Tj
Case Temperature
Tc
Input ESD protection
ESD prot
Human Body Model
2000
1_{Guaranteed by design and characterization, not 100% tested in production.}
2 _{Operation under these conditions is neither implied nor guaranteed.}
TYP
MAX UNITS NOTES
4.6
V
1,2
4.6
V
1,2
V
1
V_DD+0.5V V
1
5.5V
V
1
150
°_C
1
125
°C
1
110
°C
1
V
1
DC Electrical Characteristics - Differential Current Mode Outputs
T_A = T_{COM ;} Supply Voltage VDD = 3.3 V +/-5%
PA RAM ETER
SYMBOL
C OND ITIONS
MIN
TYP
MAX UNITS NOTES
Slew rate
dV/dt
Scope averaging on
1
2.4
4
V/ns 1, 2, 3
Slew rate matching
ΔdV/dt
Slew rate matching, Scope
averaging on
9
20
% 1, 2, 4
Rise/Fall Time Matching
ΔTrf
Rise/fall matching, Scope
averaging off
125
ps 1, 8, 9
Voltage High
Voltage Low
Statistical measurement on
VHigh
single-ended signal using
6 60
7 72
VLow
oscilloscope math function.
-1 50
9
(Scope averaging on)
850
1
mV
150
1
Max Voltage
Min Voltage
Vm ax
Vmin
Measurement on single ended
signal using absolute value.
-3 00
8 10
-1 7
1150
mV
1, 7
1, 7
Vs win g
Vswing
Scope averaging off
3 00
1 446
mV
1, 2
Crossing Voltage (abs) Vcross_abs
Scope averaging off
2 50
3 51
550
mV
1, 5
Crossing Voltage (var)
Δ-Vcross
Scope averaging off
24
140
mV
1, 6
1_{Guaranteed by design and characterization, not 100% tested in production. IREF = VDD/(3xRR). For RR = 475Ω (1%), IREF =}
2.32mA. I_OH = 6 x I_REF and V_OH = 0.7V @ Z_O=50Ω (100Ω differential impedance).
2 _{Measured from differential waveform}
3 _{Slew rate is measured through the Vswing voltage range centered around differential 0V. This results in a +/-150mV window around}
differential 0V.
4 _{Matching applies to rising edge rate for Clock and falling edge rate for Clock#. It is measured using a +/-75mV window centered on}
the average cross point where Clock rising meets Clock# falling. The median cross point is used to calculate the voltage thresholds
the oscilloscope is to use for the edge rate calculations.
5 _{Vcross is defined as voltage where Clock = Clock# measured on a component test board and only applies to the differential rising}
edge (i.e. Clock rising and Clock# falling).
6 _{The total variation of all Vcross measurements in any particular system. Note that this is a subset of V_cross_min/max (V_cross}
absolute) allowed. The intent is to limit Vcross induced modulation by setting V_cross_delta to be smaller than V_cross absolute.
7 _{Includes overshoot and undershoot.}
8 _{Measured from single-ended waveform}
9 _{Measured with scope averaging off, using statistics function. Variation is difference between min and max.}
IDT® PCIE GEN 2/3 & QPI CLOCK FOR ROMLEY-BASED SERVERS
9
932SQ420D
REV H 042012