IC-MQ_15 Datasheet, PDF (11/43 Pages) IC-Haus GmbH – Sin/Cos INTERPOLATION IC WITH RS422 DRIVER

iC-MQ PROGRAMMABLE 9-BIT
Sin/Cos INTERPOLATION IC WITH RS422 DRIVER
PROGRAMMING
Rev F3, Page 11/43
Register Map, Overview . . . . . . . . . . . . . . . . . . . Page 12
Serial Configuration Interface . . . . . . . . . . . . . Page 14
ENFAST: I²C Fast Mode Enable
ENSL:
I²C Slave Mode Enable
DEVID:
Device ID of EEPROM providing the
chip configuration data (e.g. 0x50)
CHKSUM: CRC of chip configuration data
(address range 0x00 to 0x2F)
CHPREL: Chip Release
END:
Enable Device
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 16
CFGIBN: Bias Current
CFGTA:
Temperature Monitoring
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . Page 17
MODE:
Operating Mode
Input Configuration
and Signal Path Multiplexer . . . . . . . . . . . . . . . Page 19
INMODE: Diff./Single-Ended Input Mode
RIN12:
I/V Mode and Input Resistance CH1,
CH2
BIAS12: Reference Voltage CH1, CH2
RIN0:
I/V Mode and Input Resistance CH0
BIAS0:
Reference Voltage CH0
BIASEX: Input Reference Selection
INVZ:
Index Signal Inversion
MUXIN:
Input-To-Channel Assignment:
X3...X6 to CH1, CH2
Signal Conditioning CH1, CH2 (X3...X6) . . . Page 22
GR12:
Gain Range CH1, CH2 (coarse)
GF1:
Gain Factor CH1 (fine)
GF2:
Gain Factor CH2 (fine)
VOS12:
Offset Reference Source CH1, CH2
VDC1:
Intermediate Voltage CH1
VDC2:
Intermediate Voltage CH2
OR1:
Offset Range CH1 (coarse)
OF1:
Offset Factor CH1 (fine)
OR2:
Offset Range CH2 (coarse)
OF2:
Offset Factor CH2 (fine)
PH12:
Phase Correction CH1 vs. CH2
Signal Conditioning CH0 (X1, X2) . . . . . . . . . Page 24
GR0:
Gain Range CH0 (coarse)
GF0:
Gain Factor CH0 (fine)
VOS0:
Offset Reference Source CH0
OR0:
Offset Range CH0 (coarse)
OF0:
Offset Factor CH0 (fine)
Signal Level Controller . . . . . . . . . . . . . . . . . . . . Page 25
ADJ:
Setup of ACO Output Function
Sine-To-Digital Conversion . . . . . . . . . . . . . . . . Page 26
SELRES: Resolution
SELHYS: Hysteresis
Quadrature Output Logic . . . . . . . . . . . . . . . . . . Page 27
CFGABZ: Output Logic
CFGZPOS: Zero Signal Positioning
ENZFF:
Zero Signal Synchronization
Quadrature Output Settings . . . . . . . . . . . . . . . Page 29
MTD:
Minimum Phase Distance
SIK:
Driver Short-Circuit Current
SSR:
Driver Slew Rate
TRIHL:
Driver Mode
Error Monitoring and Alarm Output . . . . . . . Page 30
EPH:
I/O Logic Alarm Output ERR
EMTD:
Min. Indication Time Alarm Output ERR
EPU:
Pull-Up Enable Alarm Output ERR
EMASKA: Error Mask Alarm Output ERR
LINECNT: Line Count Reference
EMASKO: Error Mask Driver Shutdown
PDMODE: Driver Activation
EMASKE: Error Mask EEPROM Savings
ERR1:
Error Protocol: First Error
ERR2:
Error Protocol: Last Error
ERR3:
Error Protocol: History
Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 33
EMODE: Test Mode Functions
EMODE2: Test Mode Memory Selection