PIDP-SS Datasheet, PDF (2/6 Pages) Gamewell-FCI by Honeywell – Monitor Modules with SmartScan

PID-SS Mini Monitor Module
The PID-SS Mini Monitor Module can be installed in a single-
gang junction directly behind the monitored unit. Its small size
and light weight
allow it to be in-
g2465min.wmf
stalled without
rigid mounting.
The PID-SS is in-
tended for use in
intelligent, two-
wire systems
where the indi-
vidual address of
each module is
selected using
rotary switches. It
provides a two-
wire initiating de-
vice circuit for
normally-open-
contact fire alarm
and security de-
vices.
PID-SS Applications — Use to monitor a single device or a
zone of four-wire smoke detectors, manual fire alarm pull sta-
tions, waterflow devices, or other normally-open dry-contact de-
vices. May also be used to monitor normally-open supervisory
devices with special supervisory indication at the control panel.
Monitored circuit/device is wired as an NFPA Style B (Class B)
Initiating Device Circuit. A 47K ohm End-of-Line Resistor (pro-
vided) terminates the circuit.
PID-SS Operation — Each PID-SS uses one of 99 available
module addresses on an SLC loop. It responds to regular polls
from the control panel and reports its type and the status (open/
normal/short) of its Initiating Device Circuit (IDC).
CZI-SS Interface Module
The CZI-SS Interface Module is intended for use in intelligent,
addressable systems, where the individual address of each mod-
ule is selected using built-in rotary switches. This module al-
lows intelligent panels to interface and monitor two-wire con-
ventional smoke detectors. It transmits the status (normal, open,
or alarm) of one full zone of conventional detectors back to the
control panel. All two-wire detectors being monitored must be
UL compatible with this module.
CZI-SS Applications — Use the CZI-SS to monitor a zone of
two-wire smoke detectors. The monitored circuit may be wired
as an NFPA Style B (Class B) or Style D (Class A) Initiating
Device Circuit. A 3.9 K ohm End-of-Line Resistor (provided) ter-
minates the end of the Style B or D (class B or A) circuit (maxi-
mum IDC loop resistance is 25 ohms). Install ELR across termi-
nals 8 and 9 for Style D application.
CZI-SS Operation — Each CZI-SS uses one of 99 available
module addresses on an SLC loop. It responds to regular polls
from the control panel and reports its type and the status (open/
normal/short) of its Initiating Device Circuit (IDC). A flashing LED
indicates that the module is in communication with the control
panel. The LED latches steady on alarm (subject to current limi-
tations on the loop).
Specifications
PIDP-SS
Nominal operating voltage: 15 to 32 VDC.
Maximum current draw: 5.1 mA (LED on).
Maximum operating current: 375 µA (LED flashing).
EOL resistance: 47K ohms.
Temperature range: 32°F to 120°F (0°C to 49°C).
Humidity range: 10% to 93% noncondensing.
Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x
1.25" (3.175 cm) deep. Mounts to a 4" (10.16 cm) square
x 2.125" (5.398 cm) deep box.
PID-SS
Nominal operating voltage: 15 to 32 VDC.
Maximum operating current: 375 µA.
EOL resistance: 47K ohms.
Temperature range: 32°F to 120°F (0°C to 49°C).
Humidity range: 10% to 93% noncondensing.
Dimensions: 1.3" (3.302 cm) high x 2.75" (6.985 cm) wide
x 0.5" (1.270 cm) deep.
Wire length: 6" (15.24 cm) minimum.
CZI-SS
Nominal operating voltage: 15 to 32 VDC.
Maximum current draw: 5.1 mA (LED on).
Maximum operating current: 255 µA (LED flashing).
EOL resistance: 3.9K ohms.
External supply voltage (between Terminals T3 and T4):
DC voltage: 18 to 28 volts power limited. Ripple volt-
age: 0.1 VRMS maximum. Current: 90 mA per module
maximum.
Temperature range: 32°F to 120°F (0°C to 49°C).
Humidity range: 10% to 93% noncondensing.
Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x
1.25" (3.175 cm) deep. Mounts to a 4" (10.16 cm) square
x 2.125" (5.398 cm) deep box.
DPID-SS
Normal operating voltage range: 15 to 32 VDC.
Maximum current draw: 5.7 mA (LED on).
Maximum operating current: 750 µA (LED flashing).
EOL resistance: 47K ohms.
Maximum IDC wiring resistance: 1,500 ohms.
Temperature range: 32° to 120°F (0° to 49°C).
Humidity range: 10% to 93% (non-condensing).
Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x
2.125" (5.398 cm) deep.
Page 2 of 6
PIDP-SS, PID-SS, CZI-SS, DPID-SS CS-2465 09/01/06