33984 Datasheet, PDF (12/38 Pages) Freescale Semiconductor, Inc – Dual Intelligent High-current Self-protected Silicon High Side Switch (4.0 mOhm)

ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
DYNAMIC ELECTRICAL CHARACTERISTICS
Table 5. Dynamic Electrical Characteristics
Characteristics noted under conditions 4.5 V ≤ V_DD ≤ 5.5 V, 6.0 V ≤ V_PWR ≤ 27 V, -40°C ≤ T_A ≤ 125°C, unless otherwise noted.
Typical values noted reflect the approximate parameter mean at T_A = 25°C under nominal conditions, unless otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
POWER OUTPUT TIMING
Output Rising Slow Slew Rate A (DICR D3 = 0)⁽¹⁸⁾
9.0 V < V_PWR < 16 V
Output Rising Slow Slew Rate B (DICR D3 = 0)⁽¹⁹⁾
9.0 V < V_PWR < 16 V
Output Rising Fast Slew Rate A (DICR D3 = 1)⁽¹⁸⁾
9.0 V < V_PWR < 16 V
Output Rising Fast Slew Rate B (DICR D3 = 1)⁽¹⁹⁾
9.0 V < V_PWR < 16 V
Output Falling Slow Slew Rate A (DICR D3 = 0)⁽¹⁸⁾
9.0 V < V_PWR < 16 V
Output Falling Slow Slew Rate B (DICR D3 = 0)⁽¹⁹⁾
9.0 V < V_PWR < 16 V
Output Falling Fast Slew Rate A (DICR D3 = 1)⁽¹⁸⁾
9.0 V < V_PWR < 16 V
Output Falling Fast Slew Rate B (DICR D3 = 1)⁽¹⁹⁾
9.0 V < V_PWR < 16 V
Output Turn-ON Delay Time in Fast/Slow Slew Rate⁽²⁰⁾
DICR = 0, DICR = 1
Output Turn-OFF Delay Time in Slow Slew Rate Mode⁽²¹⁾
DICR = 0
Output Turn-OFF Delay Time in Fast Slew Rate Mode⁽²¹⁾
DICR = 1
SR_{RA_SLOW}
SR_{RB_SLOW}
SR_{RA_FAST}
SR_{RB_FAST}
SR_{FA_SLOW}
SR_{FB_SLOW}
SR_{FA_FAST}
SR_{FB_FAST}
t _DLY(ON)
t _{DLY_SLOW(OFF)}
t _{DLY_FAST(OFF)}
0.2
0.03
0.4
0.03
0.2
0.03
0.8
0.1
1.0
20
10
0.6
0.1
1.0
0.1
0.6
0.1
2.0
0.35
15
230
60
V/μs
1.2
V/μs
0.3
V/μs
4.0
V/μs
1.2
V/μs
1.2
V/μs
0.3
V/μs
4.0
V/μs
1.2
μs
100
μs
500
μs
200
Direct Input Switching Frequency (DICR D3 = 0)
f _PWM
–
300
–
Hz
Notes
18. Rise and Fall Slew Rates A measured across a 5.0 Ω resistive load at high side output = 0.5 V to V_PWR-3.5 V. These parameters are
guaranteed by process monitoring.
19. Rise and Fall Slew Rates B measured across a 5.0 Ω resistive load at high side output = V_PWR-3.5 V to V_PWR-0.5 V. These parameters
are guaranteed by process monitoring.
20. Turn-ON delay time measured from rising edge of IN[0:1] signal that would turn the output ON to V_HS[0:1] = 0.5 V with R_L = 5.0 Ω resistive
load.
21. Turn-OFF delay time measured from falling edge that would turn the output OFF to V_HS[0:1] = V_PWR -0.5 V with R_L = 5.0 Ω resistive load.
33984
12
Analog Integrated Circuit Device Data
Freescale Semiconductor