SD1010 Datasheet, PDF (28/46 Pages) List of Unclassifed Manufacturers – Dual-Interface XGA TFT LCD Display Controller

SmartASIC, Inc.
SD1010
Reserve mode 7
Res threshold [7:0]
Enable SYNC
Check
Maximum VBP
Mode0 vertical size
Mode1 vertical size
Mode2 vertical size
Mode3 vertical size
Mode4 vertical size
Mode5 vertical size
Mode6 vertical size
Mode7 vertical size
Mode8 vertical size
Mode9 vertical size
Mode10 vertical size
Mode11 vertical size
Mode12 vertical size
Mode0 horizontal size
Mode1 horizontal size
Mode2 horizontal size
Mode3 horizontal size
Mode4 horizontal size
Mode5 horizontal size
Mode6 horizontal size
Mode7 horizontal size
Mode8 horizontal size
Mode9 horizontal size
Mode10 horizontal size
Mode11 horizontal size
Mode12 horizontal size
Data low threshold
Data high threshold
Edge threshold
Calibration mode
November, 1999
Revision B
8
21EH Resolution threshold for reserve mode 7
14 21FH-220H Enable SYNC polarity check during input mode
detection.
1: enable SYNC polarity based mode detection
0: disable SYNC polarity based mode detection
bit 0: 640x350 bit 1: 640x400 bit 2: 720x400
bit 3: 640x480 bit 4: 800x600 bit 5: 832x624
bit 6: 1024x768 bit 7: res mode1 bit 8: res mode2
bit 9: res mode3 bit 10: res mode4 bit 11: res mode5
bit 12: res mode6 bit 13: res mode7
8
221H The maximum vertical back porch for input video
11 222H-223H Mode0 vertical size for digital input
11 224H-225H Mode1 vertical size for digital input
11 226H-227H Mode2 vertical size for digital input
11 228H-229H Mode3 vertical size for digital input
11 22AH-22BH Mode4 vertical size for digital input
11 22CH-22DH Mode5 vertical size for digital input
11 22EH-22FH Mode6 vertical size for digital input
11 230H-231H Mode7 vertical size for digital input
11 232H-233H Mode8 vertical size for digital input
11 234H-235H Mode9 vertical size for digital input
11 236H-237H Mode10 vertical size for digital input
11 238H-239H Mode11 vertical size for digital input
11 23AH-23BH Mode12 vertical size for digital input
11 23CH-23DH Mode0 horizontal size for digital input
11 23EH-23FH Mode1 horizontal size for digital input
11 240H-241H Mode2 horizontal size for digital input
11 242H-243H Mode3 horizontal size for digital input
11 244H-245H Mode4 horizontal size for digital input
11 246H-247H Mode5 horizontal size for digital input
11 248H-249H Mode6 horizontal size for digital input
11 24AH-24BH Mode7 horizontal size for digital input
11 24CH-24DH Mode8 horizontal size for digital input
11 24EH-24FH Mode9 horizontal size for digital input
11 250H-251H Mode10 horizontal size for digital input
11 252H-253H Mode11 horizontal size for digital input
11 254H-255H Mode12 horizontal size for digital input
8
256H Low water mark for valid data.
If the data is smaller than this threshold, it is considered
LOW internally
8
257H High water mark for valid data.
If the data is larger than this threshold, it is considered
HIGH internally
8
258H Minimum difference between the data value of two
adjacent pixels to be considered as an edge
2
259H [1:0] Selects different operation modes of internal phase
calibration. The selection criterion is as follows:
0: when input video signal has large overshot,
it results in longest calibration time
1: when input video signal has median overshot,
it results in long calibration time
2: when input video signal has normal overshot,
SmartASIC Confidential
28