DS1390 Datasheet, PDF (10/24 Pages) Maxim Integrated Products – Low-Voltage SPI/3-Wire RTCs with Trickle Charger

Low-Voltage SPI/3-Wire RTCs with
Trickle Charger
Pin Description
PIN
DS1390 DS1391 DS1392 DS1393
1
1
1
1
2
2
2
2
3
3
3
3
4
4
—
—
—
—
4
4
5
5
5
5
6
6
—
—
—
—
6
—
—
9
—
6
7
7
—
—
—
—
7
7
8
8
8
8
9
—
—
9
—
—
9
—
10
10
10
10
NAME
X1
X2
V_BACKUP
CS
CE
GND
DIN
INT
RST
DOUT
I/O
SCLK
SQW/INT
SQW
V_CC
FUNCTION
Connections for Standard 32.768kHz Quartz Crystal. The internal oscillator
circuitry is designed for operation with a crystal having a 6pF specified load
capacitance (C_L). Pin X1 is the input to the oscillator and can optionally be
connected to an external 32.768kHz oscillator. The output of the internal
oscillator, pin X2, is floated if an external oscillator is connected to pin X1.
DC Backup Power Input for Primary Cell. This pin is a rechargeable
battery/super cap or a secondary supply. UL recognized to ensure against
reverse charging current when used with a lithium battery.
SPI Chip-Select Input. This pin is used to select or deselect the part.
Chip Enable for 3-Wire Interface
Ground
SPI Data Input. This pin is used to shift address and data into the part.
Interrupt Output. This pin is used to output the interrupt signal, if enabled by
the control register. The maximum voltage on this pin is 5.5V, independent
of V_CC or V_BACKUP. If enabled, INT functions when the device is powered
by either V_CC or V_BAT.
Reset. This active-low, open-drain output indicates the status of V_CC relative
to the V_PF specification. As Vcc falls below V_PF, the RST pin is driven low.
When Vcc exceeds V_PF, for t_RST, the RST pin is driven high impedance.
This pin is combined with a debounced pushbutton input function. This pin
can be activated by a pushbutton reset request. This pin has an internal,
50kΩ (typ) pullup resistor to V_CC. No external pullup resistors should be
connected. If the crystal oscillator is disabled, the startup time of the
oscillator is added to the t_RST delay.
SPI Data Output. Data is output on this pin when the part is in read mode.
CMOS push-pull driver.
Input/Output for 3-Wire Interface. CMOS push-pull driver.
Serial Clock Input. This pin is used to control the timing of data into and out
of the part.
Square-Wave/Interrupt Output. This pin is used to output the programmable
square wave or interrupt signal. When enabled by setting the ESQW bit to
logic 1, the SQW/INT pin outputs one of four frequencies: 32.768kHz,
8.192kHz, 4.096kHz, or 1Hz. This pin is open drain and requires an external
pullup resistor. The maximum voltage on this pin is 5.5V, independent of
V_CC or V_BACKUP. If enabled, SQW/INT functions when the device is
powered by either V_CC or V_BAT.
Square-Wave Output. This pin is open drain and requires an external pullup
resistor. The maximum voltage on this pin is 5.5V, independent of V_CC or
V_BACKUP. If enabled, SQW functions when the device is powered by either
V_CC or V_BAT.
DC Power Pin for Primary Power Supply
10 ____________________________________________________________________