DEMO-ATF-5X1M4E Datasheet, PDF (14/16 Pages) Broadcom Corporation. – Low Noise Enhancement Mode Pseudomorphic HEMT in a Miniature Leadless Package

0.4
0.016
0.3
0.012
1.1
0.043
0.5
0.020
0.4
0.016
0.5
0.020
0.3
0.012
Figure 3. PCB Pad Print for Minipak 1412.
Package (mm [inches ]).
This pad print provides allowance for
package placement by automated
assembly equipment without adding
excessive parasitics that could impair
the high frequency performance of
the ATF-541M4. The layout is shown
with a footprint of the ATF-541M4
superimposed on the PCB pads for
reference.
For Further Information
The information presented here is an
introduction to the use of the ATF-
541M4 enhancement mode PHEMT.
More detailed application circuit in‑
formation is available from Avago
Technologies. Consult the web page
or your local Avago Technologies sales
representative.
ATF-541M4 Die Model
Advanced_Curtice2_Model
MESFETM1
NFET=yes
Rf=
PFET=no
Gscap=2
Vto=0.3
Beta=0.888
Lambda=72e-3
Alpha=13
Tau=
Tnom=16.85
Idstc=
Cgs=1.732 pF
Cgd=0.255 pF
Gdcap=2
Fc=0.65
Rgd=0.25 Ohm
Rd=1.0125 Ohm
Ucrit=-0.72
Rg=1.7 Ohm
Vgexp=1.91
Rs=0.3375 Ohm
Gamds=1e-4
Vtotc=
Betatce=
Rgs=0.25 Ohm
Ld=
Lg=0.188 nH
Ls=
Cds=0.273 pF
Rc=195 Ohm
Crf=0.1 F
Gsfwd=
Gsrev=
Gdfwd=
Gdrev=
R1=
R2=
Vbi=0.95
Vbr=
Vjr=
Is=
Ir=
Imax=
Xti=
Eg=
N=
Fnc=1 MHz
R=0.08
P=0.2
C=0.1
Taumdl=no
wVgfwd=
wBvgs=
wBvgd=
wBvds=
wldsmax=
wPmax=
AllParams=
ATF-541M4 Minipak Model
INSIDE Package
GATE
Port
G
Num=1
SOURCE
Port
S1
Num=2
Var VAR
Egn VAR1
K=5
Z2=85
Z1=30
C
C1
C=0.28 pF
TLINP
TL1
Z=Z2/2 Ohm
L=22 mil
K=K
A=0.000
F=1 GHz
TanD=0.001
TLINP
TL2
Z=Z2/2 Ohm
L=20 0 mil
K=K
A=0.000
F=1 GHz
TanD=0.001
TLINP
TL3
Z=Z2 Ohm
L=23.6 mil
K=K
A=0.000
F=1 GHz
TanD=0.001
L
L1
L=0.234 nH
R=0.001
GaAsFET
FET1
Mode1=MESFETM1
Mode=Nonlinear
L
L6
L=0.147 nH
R=0.001
C
C2
C=0.046 pF
TLINP
TL9
Z=Z2 Ohm
L=11 mil
L
L4
L=0.281 nH
R=0.001
K=K
A=0.000
F=1 GHz
TanD=0.001
MSub
L
L7
L=0.234 nH
R=0.001
MSUB
MSub2
H=25.0 mil
Er=9.6
Mur=1
Cond=1.0E+50
Hu=3.9e+034 mil
T=0.15 mil
TanD=0
Rough=0 mil
TLINP
TL7
Z=Z2/2 Ohm
L=5.2 mil
K=K
A=0.000
F=1 GHz
TanD=0.001
TLINP
TL5
Z=Z2 Ohm
L=27.5 mil
K=K
A=0.000
F=1 GHz
TanD=0.001
SOURCE
Port
S2
Num=4
DRAIN
Port
D
Num=3
This model can be used as a design tool. It has been tested on ADS for various specifications. However, for more precise
and accurate design, please refer to the measured data in this data sheet. For future ­improvements, Avago reserves
the right to change these models without prior notice.
14