English
Language : 

ATR2406_06 Datasheet, PDF (7/25 Pages) ATMEL Corporation – Low-IF 2.4-GHz ISM Transceiver
ATR2406
6. Electrical Characteristics (Continued)
VS = 3.6V with AUX regulator, Tamb = 25°C, unless otherwise specified
No. Parameters
Test Conditions
Symbol
Min.
Typ. Max. Unit
5 Receiver Part
5.1 RX input impedance
5.2 Sensitivity
Differential
At input for BER ≤ 10-3
at 1152 kBits/s(1)
Zin
170 + j0
Ω
–93
dBm
5.3 Third order input intercept point
5.4 Intermodulation rejection
BER < 10-3, wanted at -83 dBm,
level of interferers in channels
N + 2 and N + 4(1)
5.5 Co-channel rejection
BER < 10-3, wanted at –76 dBm(1)
5.6
Adjacent channel rejection
±1.728 MHz
BER < 10-3, wanted at –76 dBm,
adjacent level referred to wanted
channel level(1)
5.7
Bi-adjacent channel rejection
±3.456 MHz
BER < 10-3, wanted at –76 dBm,
bi-adjacent level referred to wanted
channel level(1)
Rejection with ≥ 3 channels
5.8 separation
≥ ±5.128 MHz
BER < 10-3, wanted at –76 dBm,
n ≥ 3 adjacent level referred to
wanted channel level(1)
5.9 Out of band rejection > 6 MHz
BER < 10-3, wanted at –83 dBm at
2.45 GHz(1)
IIP3
IM3
RCO
Ri (N – 1)
Ri (N – 2)
Ri (n ≥ 3)
Bldf>6MHz
–15
32
–11
14
30
40
38
dBm
dBc
dBc
dBc
dBc
dBc
dBc
Out of band rejection
5.10 2300 MHz to 2394 MHz
2506 MHz to 2600 GHz
BER < 10-3, wanted at –83 dBm at
2.45 GHz(1)
Blnear
47
dBc
Out of band rejection
5.11 30 MHz to 2300 MHz
2600 MHz to 6 GHz
BER < 10-3, wanted at –83 dBm at
2.45 GHz(1)
Blfar
57
dBc
6 RSSI Part
6.1 Maximum RSSI output voltage Under high RX input signal level
6.2
RSSI output voltage, monotonic With –33 dBm at RF input
over range –96 dBm to –36 dBm With –96 dBm at RF input
VRSSImax
VRSSI
2.1
V
1.9
V
0.1
V
7 VCO
7.1
Oscillator frequency defined at
TX output
Over full temperature range(1)
2400
2483 MHz
7.2 Frequency control voltage range
VVTUNE
0.5
VCC – 0.5 V
7.3
VCO tuning input gain defined at
TX output
GVCO
240
MHz/V
Notes: 1. Measured and guaranteed only on the Atmel® evaluation board, including microstrip filter, balun, and Smart Radio Fre-
quency (Smart RF) firmware. Conducted measured.
2. Timing is determined by external loop filter characteristics. Faster timing can be achieved by modification of the loop filter.
For further information refer to the application notes.
3. The Gaussian filter control setting (GFCS) is used to compensate production tolerances by tuning the modulation deviation
in production to the nominal value of 400 kHz.
4. Burst mode with 0.9% duty cycle
7
4779L–ISM–09/06