EVAL-AD5933EB Datasheet, PDF (17/40 Pages) Analog Devices – 1 MSPS, 12-Bit Impedance Converter, Network Analyzer

Data Sheet
IMPEDANCE CALCULATION
MAGNITUDE CALCULATION
The first step in impedance calculation for each frequency point
is to calculate the magnitude of the DFT at that point.
The DFT magnitude is given by
Magnitude = R² + I ²
where:
R is the real number stored at Register Address 0x94 and
Register Address 0x95.
I is the imaginary number stored at Register Address 0x96 and
Register Address 0x97.
For example, assume the results in the real data and imaginary
data registers are as follows at a frequency point:
Real data register = 0x038B = 907 decimal
Imaginary data register = 0x0204 = 516 decimal
Magnitude = (907² + 516² ) = 1043.506
To convert this number into impedance, it must be multiplied
by
a scaling factor called the gain factor. The gain factor is
calculated during the calibration of the system with a known
impedance connected between the VOUT and VIN pins.
Once the gain factor has been calculated, it can be used in the
calculation of any unknown impedance between the VOUT and
VIN pins.
GAIN FACTOR CALCULATION
An example of a gain factor calculation follows, with the
following assumptions:
Output excitation voltage = 2 V p-p
Calibration impedance value, ZCALIBRATION = 200 kΩ
PGA Gain = ×1
Current-to-voltage amplifier gain resistor = 200 kΩ
Calibration frequency = 30 kHz
Then typical contents of the real data and imaginary data
registers after a frequency point conversion are:
Real data register = 0xF064 = −3996 decimal
Imaginary data register = 0x227E = +8830 decimal
Magnitude = (−3996)² + (8830)² = 9692.106
Gain
Factor
=

Admittance

=

1
Impedance

 Code  Magnitude
AD5933
¹ï£¶
Gain Factor
=




200 kΩ
9692.106




=
515.819
×
10 ^-12


IMPEDANCE CALCULATION USING GAIN FACTOR
The next example illustrates how the calculated gain factor
derived previously is used to measure an unknown impedance.
For this example, assume that the unknown impedance = 510
kΩ.
After measuring the unknown impedance at a frequency of
30 kHz, assume that the real data and imaginary data registers
contain the following data:
Real data register = 0xFA3F = −1473 decimal
Imaginary data register = 0x0DB3 = +3507 decimal
Magnitude = ((−1473)² + (3507)² ) = 3802.863
Then the measured impedance at the frequency point is given
by
Impedance
=
1
Gain Factor × Magnitude
=
515.819273
×
1
10 ^−
12
×
3802.863
Ω
=
509.791
k
Ω
GAIN FACTOR VARIATION WITH FREQUENCY
Because the AD5933 has a finite frequency response, the gain
factor also shows a variation with frequency. This variation in
gain factor results in an error in the impedance calculation over
a frequency range. Figure 22 shows an impedance profile based
on a single-point gain factor calculation. To minimize this error,
the frequency sweep should be limited to as small a frequency
range as possible.
101.5
101.0
VDD = 3.3V
CALIBRATION FREQUENCY = 60kHz
T_A = 25°C
MEASURED CALIBRATION IMPEDANCE = 100kΩ
100.5
100.0
99.5
99.0
98.5
54
56
58
60
62
64
66
FREQUENCY (kHz)
Figure 22. Impedance Profile Using a Single-Point Gain Factor Calculation
Rev. E | Page 17 of 40