X25F128 Datasheet, PDF (8/14 Pages) Xicor Inc. – SerialFlash™ Memory With Block Lock™ Protection

X25F128
ABSOLUTE MAXIMUM RATINGS*
Temperature Under Bias .................. –65°C to +135°C
Storage Temperature ....................... –65°C to +150°C
Voltage on any Pin with Respect to V_SS ......... –1V to +7V
D.C. Output Current ............................................. 5mA
Lead Temperature
(Soldering, 10 Seconds) ............................. 300°C
*COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only and the functional operation
of the device at these or any other conditions above
those listed in the operational sections of this specification
is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
Temp
Commercial
Extended
Industrial
Min.
0°C
–20°C
–40°C
Max.
+70°C
+85°C
+85°C
6829 PGM T06.1
Supply Voltage
X25F128
X25F128–5
Limits
1.8V to 3.6V
4.5V to 5.5V
6829 PGM T07.1
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
Symbol Parameter
I_CC V_CC Supply Current (Active)
Limits
Min.
Max.
5
I_SB1(2)
I_SB2
I_LI
I_LO
V_IL(1)
V_IH(1)
V_OL1
V_OH1
V_OL2
V_OH2
V_CC Supply Current (Standby)
V_CC Supply Current (Standby)
Input Leakage Current
Output Leakage Current
Input LOW Voltage
Input HIGH Voltage
Output LOW Voltage
Output HIGH Voltage
Output LOW Voltage
Output HIGH Voltage
–0.5
V_CC x 0.7
V_CC – 0.3
V_CC – 0.8
1
10
10
10
V_CC x 0.3
V_CC + 0.5
0.4
0.4
Units
mA
µA
µA
µA
µA
V
V
V
V
V
V
Test Conditions
SCK = V_CC x 0.1/V_CC x 0.9 @ 1MHz,
SO = OPEN, CS = V_SS
CS = V_CC, V_IN = V_SS or V_CC, V_CC = 3.6V
CS = V_CC, V_IN = V_SS or V_CC, V_CC = 5V
V_IN = V_SS to V_CC
V_OUT = V_SS to V_CC
I_OL = 1.5mA, V_CC = 2.7V
I_OH = –0.4mA, V_CC = 2.7V
I_OL = 3mA, V_CC = 5V
I_OH = –1.6mA, V_CC = 5V
6829 PGM T08.1
POWER-UP TIMING
Symbol
t_PUR(3)
t_PUW(3)
Parameter
Power-up to Read Operation
Power-up to Write Operation
Min.
Max.
1
5
Units
ms
ms
CAPACITANCE T_A = 25°C, f = 1MHz, V_CC = 5V.
6829 PGM T09
Symbol
Test
Max.
Units
Conditions
C_OUT(2)
Output Capacitance (SO)
8
pF
C_IN(2)
Input Capacitance (SCK, SI, CS, PP, HOLD)
6
pF
V_OUT = 0V
V_IN = 0V
Notes:
(1) V_IL min. and V_IH max. are for reference only and are not tested.
(2) This parameter is periodically sampled and not 100% tested.
6829 PGM T10
(3) t_PUR and t_PUW are the delays required from the time V_CC is stable until the specified operation can be initiated. These parameters
are periodically sampled and not 100% tested.
8