W3E232M16S-XSTX Datasheet, PDF (7/22 Pages) White Electronic Designs Corporation – 2x32Mx16bit DDR SDRAM

White Electronic Designs
W3E232M16S-XSTX
PRELIMINARY*
NO OPERATION (NOP)
The NO OPERATION (NOP) command is used to perform
a NOP to the selected DDR SDRAM (CS# is LOW while
RAS#, CAS#, and WE# are high). This prevents unwanted
commands from being registered during idle or wait states.
Operations already in progress are not affected.
LOAD MODE REGISTER
The Mode Registers are loaded via inputs A0-12. The
LOAD MODE REGISTER command can only be issued
when all banks are idle, and a subsequent executable
command cannot be issued until tMRD is met.
FIGURE 3 – MODE REGISTER DEFINITION
BA1 BA0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 Address Bus
14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 ^{Mode Register (Mx)}
0*
0*
Operating Mode
CAS Latency BT Burst Length
* M14 and M13
(BA0 and BA1 must be
"0, 0" to select
the base mode register
(vs. the extended
mode register).
M2 M1 M0
0 00
0 01
0 10
0 11
1 00
1 01
1 10
1 11
Burst Length
M3 = 0
Reserved
2
4
8
Reserved
Reserved
Reserved
Reserved
M3 = 1
Reserved
2
4
8
Reserved
Reserved
Reserved
Reserved
M3
0
1
M6 M5 M4
0 00
0 01
0 10
0 11
1 00
1 01
1 10
1 11
Burst Type
Sequential
Interleaved
CAS Latency
Reserved
Reserved
2
Reserved
Reserved
Reserved
2.5
Reserved
M12 M11 M10 M9
M8
M7
M6-M0
Operating Mode
0
0
0
0
0
0
Valid
Normal Operation
0
0
0
0
1
0
Valid
Normal Operation/Reset DLL
-
-
-
-
-
-
-
All other states reserved
ACTIVE
The ACTIVE command is used to open (or activate) a
row in a particular bank for a subsequent access. The
value on the BA0, BA1 inputs selects the bank, and
the address provided on inputs A0-12 selects the row.
This row remains active (or open) for accesses until
a PRECHARGE command is issued to that bank. A
PRECHARGE command must be issued before opening
a different row in the same bank.
READ
The READ command is used to initiate a burst read access
to an active row. The value on the BA0, BA1 inputs selects
the bank, and the address provided on inputs A0-9 selects
the starting column location. The value on input A10
determines whether or not AUTO PRECHARGE is used. If
AUTO PRECHARGE is selected, the row being accessed
will be precharged at the end of the READ burst; if AUTO
PRECHARGE is not selected, the row will remain open
for subsequent accesses
WRITE
The WRITE command is used to initiate a burst write
access to an active row. The value on the BA0, BA1 inputs
will be precharged at the end of the READ burst; if AUTO
PRECHARGE is not selected, the row will remain open
for subsequent accesses
PRECHARGE
The PRECHARGE command is used to deactivate the
open row in a particular bank or the open row in all banks.
The bank(s) will be available for a subsequent row access
a specified time (tRP) after the PRECHARGE command is
issued. Except in the case of concurrent auto precharge,
where a READ or WRITE command to a different bank is
allowed as long as it does not interrupt the data transfer
in the current bank and does not violate any other timing
parameters. Input A10 determines whether one or all
banks are to be precharged, and in the case where only
one bank is to be precharged, inputs BA0, BA1 select the
bank. Otherwise BA0, BA1 are treated as “Don’t Care.”
Once a bank has been precharged, it is in the idle state and
must be activated prior to any READ or WRITE commands
being issued to that bank. A PRECHARGE command will
be treated as a NOP if there is no open row in that bank
(idle state), or if the previously open row is already in the
White Electronic Designs Corp. reserves the right to change products or specifications without notice.
December 2005
Rev. 1
7
White Electronic Designs Corporation • [phone] • www.wedc.com