594D Datasheet, PDF (9/9 Pages) Vishay Siliconix – Solid Tantalum Chip Capacitors TANTAMOUNT, Conformal Coated, Maximum CV, Low ESR

594D
Vishay Sprague
TAPE AND REEL PACKAGING in inches [millimeters]
Note: Metric dimensions will govern. Dimensions in inches are rounded and for reference only.
T₂
Max.
.024 [0.600]
Max.
Deformation
Between .059 + .004 - 0.0
Embossments [1.5 + 0.10 - 0.0]
.157 ± .004
[4.0 ± 0.10]
10 Pitches Cumulative
Tolerance on Tape
± 0.008 [0.2]
.069 ± .004
.079 ± .002
[2.0 ± 0.05]
Embossment
[1.75 ± 0.10]
B₁ Max.
(Note 6)
K₀
Top
Cover
Tape
.004 [0.10]
Max.
For Tape Feeder
Reference only
including draft.
Concentric around B₀
(Note 5)
Top
Cover
Tape
A₀
B₀
.030 [0.75]
Min. (Note 3) F _W
.030 [0.75]
Min. (Note 4)
Center Lines
P
of Cavity
1
D₁ Min. For Components
.079 x .047 [2.0 x 1.2] and Larger.
USER DIRECTION OF FEED
(Note 5)
Maximum Cavity
Size (Note 1)
Cathode (-)
20°
Maximum
Component
Rotation
(Side or Front Sectional View)
Anode (+)
DIRECTION OF FEED
20° Maximum
Component Rotation
Typical
Component
B₀
Cavity
Center Line
A₀
(Top View)
Typical
Component
Center Line
3.937 [100.0]
.039 [1.0]
Max.
Tape
.039 [1.0] Max.
9.843 [250.0]
Camber
(Top View)
Allowable Camber to be .039/3.937 [1/100]
Non-Cumulative Over 9.843 [250.0]
Tape and Reel Specifications: All case codes are available
on plastic embossed tape per EIA-481-1. Tape reeling per
IEC 286-3 is also available. Standard reel diameter is 7"
[178mm]. 13" [330mm] reels are available and recommended
as the most cost effective packaging method.
The most efficient packaging quantities are full reel increments
on a given reel diameter. The quantities shown allow for the
sealed empty pockets required to be in conformance with
EIA-481-1. Reel size and packaging orientation must be
specified in the Vishay Sprague part number.
TAPE
SIZE
12mm
12mm
Double Pitch
B(N_{1 o(Mteax6.))}
0.323
[8.2]
0.323
[8.2]
D(N_{1 o(Mtein5.))}
0.059
[1.5]
0.059
[1.5]
F
0.217 ± 0.002
[5.5 ± 0.05]
0.453 ± 0.004
[11.5 ± 0.03]
P₁
0.157 ± 0.004
[4.0 ± 0.1]
0.315 ± 0.004
[8.0 ± 0.1]
R (Min.)
(Note 2)
1.181
[30.0]
1.181
[30.0]
(MTa²x.)
0.256
[6.5]
0.256
[6.5]
W
0.472 ± 0.012
[12.0 ± 0.30]
0.945 ± 0.012
[24.0 ± 0.03]
A₀ B₀ K₀
(Note 1)
Notes:
1. A₀B₀K₀ are determined by the maximum dimensions to the ends of the terminals extending from the component body and/or the body
dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of
the cavity (A₀B₀K₀) must be within 0.002" [0.05mm] minimum and 0.020" [0.50mm] maximum. The clearance allowed must also prevent
rotation of the component within the cavity of not more than 20 degrees.
2. Tape with components shall pass around radius "R" without damage. The minimum trailer length may require additional length to
provide R minimum for 12mm embossed tape for reels with hub diameters approaching N minimum.
3. This dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape between the
embossed cavities or to the edge of the cavity whichever is less.
4. This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the
carrier tape between the embossed cavity or to the edge of the cavity whichever is less.
5. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of
embossment location and hole location shall be applied independent of each other.
6. B₁ dimension is a reference dimension for tape feeder clearance only.
www.vishay.com
74
For technical questions, contact [e-mail]
Document Number 40006
Revision 09-Mar-05