594D Datasheet, PDF (1/9 Pages) Vishay Siliconix – Solid Tantalum Chip Capacitors TANTAMOUNT, Conformal Coated, Maximum CV, Low ESR

594D
Vishay Sprague
Solid Tantalum Chip Capacitors
TANTAMOUNT^®, Conformal Coated, Maximum CV,
Low ESR
FEATURES
• New extended range offerings.
• Large capacitance rating range.
• Lowest ESR for a surface mount tantalum chip capacitor.
• 100% surge current conditioning for C, D and R cases.
• Terminations: Tin (2) standard.
• 8mm, 12mm tape and reel packaging available per EIA-
481-1 and IEC 286-3. 7” [178mm] standard. 13”
[330mm] available.
• Case code compatibility with EIA 535BAAE and
CECC30801 molded chips.
PERFORMANCE / ELECTRICAL CHARACTERISTICS
Operating Temperature: -55˚C to +85˚C, (to -125˚C with
voltage derating.)
Capacitance Tolerance: ±10%, ±20% standard.
Voltage Rating: 4 WVDC to 50WVDC.
Capacitance Range: 1.0µF to 1500µF.
Equivalent Series Resistance: ESR readings measured
at 100kHz, +25°C from 3500 milliohm to 30 milliohm.
ORDERING INFORMATION
594D
TYPE
477
CAPACITANCE
X0
004
CAPACITANCE DC VOLTAGE RATING
TOLERANCE
@ + 85°C
R
2
CASE CODE TERMINATION
T
PACKAGING
This is expressed in
picofarads.
The first two digits are
the significant figures.
The third is the number
of zeros to follow.
X0 = ± 20%
X9 = ± 10%
This is expressed in volts.
To complete the three-
digit block, zeros precede
the voltage rating. A
decimal point is indicated
by an "R"
(6R3 = 6.3 volts).
Note: Preferred Tolerance and reel sizes are in bold.
See Ratings
and Case
Codes Table.
2 = 100% Tin
4 = Gold Plated
7 = Hot Solder
Dipped
8 = Solder
Plated (60/40)
Special Order.
T = Tape and Reel
7" [178mm] Reel
W = 13” [330mm]Reel
- See Tape and
Reel specifications
We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size. Voltage
substitutions will be marked with the higher voltage rating.
DIMENSIONS in inches [millimeters]
W
Tantalum Wire Nib
Identifies Anode (+)
Terminal
L
Max.
D
Ref.
B
J
Max.
J
Max.
A
H
CASE
CODE
B
C
D
R
L (Max.)
0.158
[4.0]
0.281
[7.1]
0.293
[7.5]
0.283
[7.2]
W
H
A
0.110 + 0.012 - 0.016 0.075 + 0.012 - 0.024 0.031 ± 0.012
[2.8 + 0.3 - 0.4]
[1.9 + 0.3 - 0.6] [0.80 ± 0.30]
0.126 ± 0.12
[3.2 ± 0.3]
0.098 ± 0.012
[2.5 ± 0.3]
0.051 ± 0.012
[1.3 ± 0.30]
0.170 ± 0.012
[4.3 ± 0.3]
0.110 ± 0.012
[2.8 ± 0.3]
0.051 ± 0.012
[1.3 ± 0.30]
0.235 ± 0.012
[6.0 ± 0.3]
0.136 ± 0.012
[3.5 ± 0.3]
0.051 ± 0.012
[1.3 ± 0.30]
Note: The anode termination (D less B) will be a minimum of 0.012" [0.3mm].
B
0.097 ± 0.016
[2.5 ± 0.4]
0.180 ± 0.024
[4.6 ± 0.6]
0.180 ± 0.024
[4.6 ± 0.6]
0.180 ± 0.024
[4.6 ± 0.6]
www.vishay.com
66
For technical questions, contact [e-mail]
D (Ref.)
0.138
[3.5]
0.236
[6.0]
0.253
[6.4]
0.243
[6.2]
J (Max.)
0.004
[0.1]
0.004
[0.1]
0.004
[0.1]
0.004
[0.1]
Document Number 40006
Revision 09-Mar-05