DG611A_11 Datasheet, PDF (6/15 Pages) Vishay Siliconix – 1 pC Charge Injection, 100 pA Leakage, Quad SPST Switches

DG611A, DG612A, DG613A
Vishay Siliconix
SPECIFICATIONS FOR UNIPOLAR SUPPLIES (V + = + 3 V, V - = 0 V)
Parameter
Analog Switch
Symbol
Test Conditions
Unless Otherwise Specified
V+ = + 3 V, V- = 0 V
V_IN = 1.4 V, 0.6 V^a
Temp.^b
Typ.^c
- 40 °C to 125 °C - 40 °C to 85 °C
Min.^d Max.^d Min.^d Max.^d
Analog Signal Range^e
V_ANALOG
Full
0
3
0
3
On-Resistance
R_ON
I_S = 1 mA, V_D = + 1.5 V
Room 195
Full
235
235
300
280
Switch Off
Leakage Current
I_S(off)
I_D(off)
V + = 3.3 V, V- = 0 V
V_D = 3 V/0.3 V
V_S = 0.3 V/3 V
Room
Full
Room
Full
± 0.02
± 0.02
- 0.1
-2
- 0.1
-2
0.1 - 0.1 0.1
2 - 0.25 0.25
0.1 - 0.1 0.1
2 - 0.25 0.25
Switch On
Leakage Current
I_D(on)
V + = 3.3 V, V- = 0 V
V_D = V_S = 0.3 V/3 V
Room ± 0.02
Full
- 0.1
-6
0.1 - 0.1 0.1
6 - 0.25 0.25
Digital Control
Input Current, V_IN Low
I_IL
V_IN Under Test = 0.6 V
Full 0.005 - 0.1 0.1 - 0.1 0.1
Input Current, V_IN High
Input Capacitance^e
I_IH
V_IN Under Test = 1.4 V
Full 0.005 - 0.1 0.1 - 0.1 0.1
C_IN
f = 1 MHz
Room
2
Dynamic Characteristics
Turn-On Time
Turn-Off Time
t_ON
Room
87
R_L = 300 , C_L = 35 pF
Full
t_OFF
V_S = 2 V, see figure 1
Room
33
Full
125
125
180
170
55
55
65
60
Break-Before-Make
Time Delay
t_BBM
DG613 only, V_S = 2 V
Room
60
R_L = 300 , C_L = 35 pF
Full
10
10
Charge Injection^e
Q
V_g = 0 V, R_g = 0 , C_L = 1 nF Room
2.3
Off Isolation^e
Channel-to-Channel
Crosstalk^e
OIRR
X_TALK
R_L = 50 , C_L = 5 pF
f = 10 MHz
Room - 60
Room - 90
3 dB Bandwidth^e
BW
R_L = 50 , C_L = 5 pF
Room 550
Source Off Capacitance^e
Drain Off Capacitance^e
C_S(off)
C_D(off)
f = 1 MHz; V_S = 0 V
Room
5
Room
6
Drain On Capacitance^e
C_D(on)
f = 1 MHz; V_S = V_D = 0 V Room
9
Power Supplies
Power Supply Current
I+
Room 0.001
0.1
0.1
Full
1
1
Negative Supply Current
I-
V_IN = 0 V or 3 V
Room - 0.001 - 0.1
Full
-1
- 0.1
-1
Ground Current
I_GND
Room - 0.001 - 0.1
Full
-1
- 0.1
-1
Unit
V

nA
µA
pF
ns
pC
dB
MHz
pF
µA
Notes:
a. V_IN = input voltage to perform proper function.
b. Room = 25 °C, Full = as determined by the operating temperature suffix.
c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
e. Guaranteed by design, not subject to production test.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
www.vishay.com
Document Number: 69904
6
S11-1066-Rev. C, 30-May-11
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000