MMU-0102-VG03 Datasheet, PDF (5/8 Pages) Vishay Siliconix – MELF Resistors with Established Reliability

MMU 0102 VG03, MMA 0204 VG03, MMB 0207 VG03
MELF Resistors with Established Reliability
Vishay Beyschlag
DESCRIPTION
Production is strictly controlled and follows an extensive
set of instructions established for reproducibility. A
homogeneous film of metal alloy is deposited on a high grade
ceramic body (Al₂O₃) and conditioned to achieve the desired
temperature coefficient. Nickel plated steel termination caps
are firmly pressed on the metallized rods. A special laser is
All products comply with the GADSL ⁽¹⁾ and the
CEFIC-EECA-EICTA ⁽²⁾ list of legal restrictions on
hazardous substances. This includes full compliance with
the following directives:
 2000/53/EC End of Vehicle Life Directive (ELV) and
Annex II (ELV II)
 2011/65/EU Restriction of the use of Hazardous
used to achieve the target value by smoothly cutting a helical
Substances directive (RoHS)
groove in the resistive layer without damaging the ceramics.
The resistor elements are covered by a protective coating
designed for electrical, mechanical and climatic protection.
 2002/96/EC Waste Electrical and Electronic Equipment
Directive (WEEE)
The terminations receive a final pure tin on nickel plating.
Five color code rings designate the resistance value and
tolerance in accordance with IEC 60062 ⁽³⁾.
APPROVALS
The resistors are approved within the IECQ-CECC Quality
Assessment System for Electronic Components to the detail
The result of the determined production is verified by an
specification EN 140401-803 which refers to EN 60115-1,
extensive testing procedure performed on 100 % of the
individual resistors. This includes pulse load screening (for
R  10 ) and additional non-linearity screening (for
R  30 ) for the elimination of products with a potential risk
of early life failures according to EN 140401-803, 2.1.2.2.
Only accepted products are laid directly into the blister tape
in accordance with IEC 60286-3 ⁽³⁾, Type II. Products within
a package unit are from the same production lot and carry
the same date code.
ASSEMBLY
The resistors are suitable for processing on automatic SMD
assembly systems. They are suitable for automatic soldering
EN 140400 and the variety of environmental test procedures
of the IEC 60068 ⁽³⁾ series.
Conformity is attested by the use of the CECC logo ( ) as
the mark of conformity on the package label.
Vishay BEYSCHLAG has achieved “Approval of
Manufacturer” in accordance with IEC QC 001002-3,
clause 2. The release certificate for “Technology Approval
Schedule” in accordance with CECC 240001 based on
IEC QC 001002-3, clause 6 is granted for the
Vishay BEYSCHLAG manufacturing process.
The Vishay BEYSCHLAG production facility is registered
with the CAGE code D9539.
using wave, reflow or vapour phase as shown in
IEC 61760-1 ⁽³⁾. Solderability is specified for 2 years after
production or requalification, however, excellent solderability
is proven after extended storage in excess of 10 years. The
permitted storage time is 20 years.
The resistors are completely lead (Pb)-free, the pure tin
plating provides compatibility with lead (Pb)-free soldering
processes. The immunity of the plating against tin whisker
growth has been proven under extensive testing.
RELATED PRODUCTS
A wider range of TCR, tolerance and resistance values, plus
the option of values from a different E series is available with
products approved to EN 140401-803, Version A, without
established reliability, nominal failure rate level E0 (quality
factor _Q = 3). See the datasheets:
 “Professional MELF Resistors”
(www.vishay.com/doc?28713)
 “Precision MELF Resistors”
The encapsulation is resistant to all cleaning solvents
(www.vishay.com/doc?28714)
commonly used in the electronics industry, including
 “High Precision MELF Resistor”
alcohols, esters and aqueous solutions. The suitability of
(www.vishay.com/doc?28715)
conformal coatings, if applied, shall be qualified by
appropriate means to ensure the long-term stability of the
whole system.
Notes
(1) _{Global Automotive Declarable Substance List, see www.gadsl.org.}
(2) _{CEFIC (European Chemical Industry Council), EECA (European Electronic Component Manufacturers Association), EICTA (European trade}
organisation representing the information and communications technology and consumer electronics), see www.eicta.org/index.php?id=995
 issues  environment policy  chemicals  chemicals for electronics.
(3) _{The quoted IEC standards are also released as EN standards with the same number and identical contents.}
Document Number: 28707
for technical questions, contact: [e-mail]
www.vishay.com
Revision: 21-May-12
63
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000