K3010P_12 Datasheet, PDF (2/7 Pages) Vishay Siliconix – Optocoupler, Phototriac Output, Non-Zero Crossing

www.vishay.com
K3010P, K3010PG Series
Vishay Semiconductors
ABSOLUTE MAXIMUM RATINGS (T_amb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
INPUT
Reverse voltage
Forward current
Forward surge current
Power dissipation
Junction temperature
OUTPUT
t_p ≤ 10 μs
V_R
5
V
I_F
80
mA
I_FSM
3
A
P_diss
100
mW
T_j
100
°C
Off state output terminal voltage
On state RMS current
Peak surge current, non-repetitive
Power dissipation
Junction temperature
COUPLER
t_p ≤ 10 ms
V_DRM
250
V
I_TRM
100
mA
I_TMS
1.5
A
P_diss
300
mW
T_j
100
°C
Isolation test voltage (RMS)
Total power dissipation
Storage temperature range
Ambient temperature range
Soldering temperature ⁽¹⁾
t=1s
2 mm from case, t ≤ 10 s
V_ISO
P_tot
T_stg
T_amb
T_sld
5300
350
- 55 to + 150
- 55 to + 100
260
V_RMS
mW
°C
°C
°C
Notes
• Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not
implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute
maximum ratings for extended periods of the time can adversely affect reliability.
(1) _{Refer to wave profile for soldering conditions for through hole devices (DIP) “Assembly Instructions” (www.vishay.com/doc?80054)}
ELECTRICAL CHARACTERISTICS (T_amb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
PART
SYMBOL MIN. TYP. MAX. UNIT
INPUT
Forward voltage
Junction capacitance
OUTPUT
I_F = 50 mA
V_R = 0, f = 1 MHz
V_F
1.25
1.6
V
C_j
50
pF
Forward peak off-state voltage
(repetitive)
I_RDM = 100 nA
V_DRM ⁽¹⁾
250
V
Peak on-state voltage
Critical rate of rise of off-state voltage
COUPLER ⁽²⁾
I_TM = 100 mA
I_FT = 0, I_FT = 30 mA
V_TM
1.5
dV/d_tcr
10
dV/d_tcrq
0.1
0.2
3
V
V/μs
V/μs
Collector emitter trigger current
Holding current
K3010P
I_FT
K3010PG
I_FT
V_S = 3 V, R_L = 150 Ω
K3011P
K3011PG
I_FT
I_FT
K3012P
I_FT
K3012PG
I_FT
I_F = 10 mA, V_S ≥ 3 V
I_H
8
15
mA
8
15
mA
5
10
mA
5
10
mA
2
5
mA
2
5
mA
100
μA
Notes
• Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering
evaluation. Typical values are for information only and are not part of the testing requirements.
(1) _{Test voltage must be applied within dV/dt ratings.}
(2) _{IFT is defined as a minimum trigger current.}
Rev. 2.2, 01-Jun-12
2
Document Number: 83504
For technical questions, contact: [e-mail]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000