PI3303-00-EVAL1 Datasheet, PDF (5/42 Pages) Vicor Corporation – Cool-Power® ZVS Switching Regulators

PI33xx-x0
Pin Description
Pin Name
SGND
PGND
VIN
VOUT
VS1
PWRGD
EAO
EN
REM
ADJ
TRK
NC
VDR
SYNCO
SYNCI
SDA
SCL
ADR1
ADR0
Number
Block 1
Block 2
Block 3
Block 5
Block 4
A1
A2
A3
A5
B1
C1
A4
K3
K4
K5
D1
E1
H1
G1
Description
Signal Ground: Internal logic ground for EA, TRK, SYNCI, SYNCO, ADJ and I²C (options) communication returns. SGND
and PGND are star connected within the regulator package.
Power Ground: V_IN and V_OUT power returns.
Input Voltage: and sense for UVLO, OVLO and feed forward ramp.
Output Voltage: and sense for power switches and feed-forward ramp.
Switching Node: and ZVS sense for power switches.
Power Good: High impedance when regulator is operating and V_OUT is in regulation.
Otherwise pulls to SGND. Also can be used for parallel timing management intended for lead regulator.
Error Amp Output: External connection for additional compensation and current sharing.
Enable Input: Regulator enable control. Asserted high or left floating – regulator enabled;
Asserted low, regulator output disabled. Polarity is programmable via I²C interface.
Remote Sense: High side connection. Connect to output regulation point.
Adjust Input: An external resistor may be connected between ADJ pin and SGND or VOUT
to trim the output voltage up or down.
Soft-start and Track Input: An external capacitor may be connected between TRK pin
and SGND to decrease the rate of rise during soft-start.
No Connect: Leave pins floating.
VDR can only be used for ADR0 and ADR1 pull up reference voltage.
No other external loading is permitted
Synchronization Output: Outputs a low signal for ½ of the minimum period for synchronization of other converters.
Synchronization Input: Synchronize to the falling edge of external clock frequency.
SYNCI is a high impedance digital input node and should always be connected to SGND when not in use.
Data Line: Connect to SGND for PI33xx-00. For use with PI33xx-20 only.
Clock Line: Connect to SGND for PI33xx-00. For use with PI33xx-20 only.
Tri-state Address: No connect for PI33xx-00. For use with PI33xx-20 only.
Tri-state Address: No connect for PI33xx-00. For use with PI33xx-20 only.
Package Pin-Out
PGND
Block 2
1 2 3 4 5 6 7 8 9 10 11 12 13 14
SGND ^K
Block 1
J
ADR1 H
VIN
Block 3
ADR0 G
SGND F
SCL E
SDA D
TRK C
ADJ B
VS1
Block 4
PWRGD A
VOUT
Block 5
Cool-Power^® ZVS Switching Regulators
Page 5 of 42
Rev 2.4
02/2017
Block 1: B2-4, C2-4, D2-3, E2-3, F1-3, G2-3, H2-3, J1-3, K1-2
Block 2: A8-10, B8-10, C8-10, D8-10, E4-10,
F4-10, G4-10, H4-10, J4-10, K6-10
Block 3: G12-14, H12-14, J12-14, K12-14
Block 4: A12-14, B12-14, C12-14, D12-14, E12-14
Block 5: A6-7, B6-7, C6-7, D6-7
vicorpower.com
800 927.9474