TL16PNP200A Datasheet, PDF (4/24 Pages) Texas Instruments – STANDALONE PLUG-AND-PLAY (PnP) CONTROLLER

TL16PNP200A
STANDALONE PLUG-AND-PLAY (PnP) CONTROLLER
SLLS274A– APRIL1997 – REVISED MAY 1997
Terminal Functions
TERMINAL
NAME^†
I/O
NO.
DESCRIPTION
A15-A0
11-26 I Address. A15-A0 connects to ISA address bits SA15-SA0.
A16 (INTR2),
A17 (INTR3),
A18 (INTR4)
9-7
I Address (Interrupt). In mode 0, A16–A18 must be connected to ISA address bits SA16, LA17, and LA18
respectively. In Mode 1, INTR2–INTR4 are interrupt requests from logical devices 2, 3, and 4 respectively.
A19 (CDACK3),
6, 5
I Address (DMA acknowledge). In mode 0, A19–A20 must be connected to ISA address bits LA19 and LA20.
A20 (CDACK4)
In mode 1, CDACK3 and CDACK4 are configurable data acknowledge signals and must be connected to
the ISA DACK signals of the selected DMA channels as specified by DMA mapping in the power-up
defaults.
A21 (CDRQ3),
A22 (CDRQ4)
4, 3 I/O Address (DMA request). In mode 0, A21 and A22 are inputs that must be connected to ISA address bits
LA21 and LA22. In mode 1, CDRQ3 and CDRQ4 are configurable data request outputs and must be
connected to the ISA DRQ signals of the selected DMA channels as specified by DMA mapping in the
power-up defaults.
A23 (IOCS4)
2 I/O Address (I/O chip select). In mode 0, A23 is an input that must be connected to ISA address bit LA23. In
mode 1, IOCS4 is an I/O chip select output for logical device 4.
AEN
40
I ISA address enable. During DMA operation, AEN is an active signal that prevents the controller from
generating an I/O chip select.
BALE (OEN1)
80 I/O ISA bus address latch enable (output enable). In mode 0, BALE is an ISA input which is used to latch the
upper address. In mode 1, OEN1 is an output enable and can be configured to respond to I/O read
operations to any logical device, which can use it to enable its transceivers.
CDACK0,
CDACK1,
CDACK2
45-43
I Configurable ISA DMA acknowledge. CDACK0 – CDACK2 must be connected to the ISA DACK signals
of the selected DMA channels as specified by DMA mapping in the power-up defaults.
CDRQ0, CDRQ1, 49-47 O Configurable ISA DMA data request. CDRQ0–CDRQ2 must be connected to the ISA DRQ signals of the
CDRQ2
selected DMA channels as specified by DMA mapping in the power-up defaults.
CLK
42
I 10- to 22–MHz clock. CLK is an input from the OSC signal on the ISA bus.
D0-D7
36-33, I/O 8-bit ISA data
31-28
DMA_ACK0,
DMA_ACK1
67, 66 O DMA acknowledge. DMA_ACK0 and DMA_ACK1 are used for DMA acknowledge to logical devices 0 and
1.
DMA_RQ0,
DMA_RQ1
71, 70 I DMA requests. DMA_RQ0 and DMA_RQ1 are used for DMA requests from logical devices 0 and 1.
GND
1, 27,
37, 61,
74
Ground (0 V). GND terminals must be tied to ground for proper operation.
INTR0, INTR1
73, 72 I Interrupt requests. INTR0 and INTR1 generate interrupt requests from logical devices 0 and 1.
IOCS0, IOCS1
75, 76 O I/O chip select outputs to logical devices 0 and 1. The address decoder decodes the full 16-bit I/O address
and generates the I/O chip select signals based on the selected I/O block size.
IOR
38
I ISA I/O read.
IOW
39
I ISA I/O write.
IRQ3–IRQ7,
IRQ9–IRQ12,
IRQ14, IRQ15
60-50 O ISA Interrupt request. These signals must be connected to the corresponding ISA IRQ signals.
MCS0(IOCS3),
MCS1(IOCS2)
78, 77 O Memory chip select (I/O chip select). In mode 0, MCS0 and MCS1 are the memory chip select outputs for
logical devices 0 and 1. A 24-bit memory address is decoded to generate the memory chip select signals
based on the selected memory block size. In mode 1, IOCS3 and IOCS2 are the I/O chip select outputs
for logical devices 3 and 2.
OEN0
79
O Output enable. OEN0 can be configured to respond to I/O read operations to any logical device, which can
use it to enable its transceivers.
† _{Terminal names in parenthesis indicate the device is in mode 1 operation.}
4
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265