THS4021_16 Datasheet, PDF (3/29 Pages) Texas Instruments – 350-MHz LOW-NOISE HIGH-SPEED AMPLIFIERS

THS4021
THS4022
www.ti.com
SLOS265C – SEPTEMBER 1999 – REVISED JULY 2007
ABSOLUTE MAXIMUM RATINGS⁽¹⁾
over operating free-air temperature range (unless otherwise noted)
V_CC
Supply voltage
V_I
Input voltage
I_O
Output current
V_IO
Differential input voltage
Continuous total power dissipation
T_J
Maximum junction temperature
Operating free-air temperature: C-suffix
T_A
I-suffix
T_stg
Storage temperature
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds
VALUE
±16.5
±V_CC
150
±4
See Dissipation Ratings table
150
0 to 70
–40 to 85
–65 to 150
300
UNIT
V
V
mA
V
°C
°C
°C
°C
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
DISSIPATION RATINGS
PACKAGE
D ⁽¹⁾
DGN ⁽²⁾
θ_JA
(°C/W)
167
58.4
θ_JC
(°C/W)
38.3
4.7
T_A = 25°C
POWER RATING
740 mW
2.14 W
(1) This data was taken using the JEDEC standard low-K test PCB. For the JEDEC proposed high-K test PCB, the θ_JA is 95°C/W with a
power rating at T_A = 25°C of 1.32 W.
(2) This data was taken using 2-oz. (0.071-mm thick) trace and copper pad on a 3-in. × 3-in. (7.62-cm × 7.62-cm) PCB, with the device
soldered directly to the board. For further information, see the Application Information section of this data sheet.
RECOMMENDED OPERATING CONDITIONS
V_CC+ and V_CC–
T_A
Supply voltage
Operating free-air temperature
Dual supply
Single supply
C-suffix
I-suffix
MIN
NOM
MAX UNIT
±4.5
±16
V
9
32
0
70
°C
–40
85
ELECTRICAL CHARACTERISTICS
at T_A = 25°C, V_CC = ±15 V, R_L = 150 Ω (unless otherwise noted)
PARAMETER
TEST CONDITIONS
Dynamic Performance
V_CC = ±15 V
Small-signal bandwidth
(–3 dB)
V_CC = ±5 V
V_CC = ±15 V
BW
V_CC = ±5 V
Bandwidth for 0 1-dB flatness ^{VCC = ±15 V}
V_CC = ±5 V
Gain = 10
Gain = 20
Gain = 10
Full power bandwidth⁽¹⁾
V_O(pp) = 20 V, V_CC = ±15 V
V_O(pp) = 5 V, V_CC = ±5 V
SR
Slew rate⁽²⁾
V_CC = ±15 V, 10-V step
V_CC = ±5 V, 5-V step
Gain = 10
MIN
TYP
MAX UNIT
350
280
80
70
MHz
17
17
3.7
11.8
470
V/μs
370
(1) Full-power bandwidth = slew rate / 2π V_O(Peak).
(2) Slew rate is measured from an output level range of 25% to 75%.
Copyright © 1999–2007, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): THS4021 THS4022