VCE6467T Datasheet, PDF (275/352 Pages) Texas Instruments – VCE6467T, AVCE6467T Digital Media System-on-Chip

VCE6467T, AVCE6467T
www.ti.com
HEX ADDRESS
RANGE
0x01C6 4418
0x01C6 441A
0x01C6 441A
0x01C6 441B
0x01C6 441B
0x01C6 441C
0x01C6 441D
0x01C6 441F
0x01C6 4420
0x01C6 4424
0x01C6 4428
0x01C6 442C
0x01C6 4430
0x01C6 4460
0x01C6 4462
0x01C6 4463
0x01C6 4464
0x01C6 4466
0x01C6 4480
0x01C6 4482
0x01C6 4483
0x01C6 4484
0x01C6 4486
0x01C6 4487
0x01C6 4488
0x01C6 448A
0x01C6 448B
SPRS690 – MARCH 2011
Table 6-86. USB2.0 Registers (continued)
ACRONYM
REGISTER NAME
COUNT0
Number of received bytes in Endpoint 0 FIFO. (Index register set to select
Endpoint 0)
RXCOUNT
Number of bytes in host RX endpoint FIFO. (Index register set to select
Endpoints 1 - 4)
HOST_TYPE0
Defines the speed of Endpoint 0
HOST_TXTYPE
Sets the operating speed, transaction protocol and peripheral endpoint number
for the host TX endpoint. (Index register set to select Endpoints 1 - 4 only)
HOST_NAKLIMIT0
Sets the NAK response timeout on Endpoint 0. (Index register set to select
Endpoint 0)
HOST_TXINTERVAL
Sets the polling interval for Interrupt/ISOC transactions or the NAK response
timeout on Bulk transactions for host TX endpoint. (Index register set to select
Endpoints 1 - 4 only)
HOST_RXTYPE
Sets the operating speed, transaction protocol and peripheral endpoint number
for the host RX endpoint. (Index register set to select Endpoints 1 - 4 only)
HOST_RXINTERVAL
Sets the polling interval for Interrupt/ISOC transactions or the NAK response
timeout on Bulk transactions for host RX endpoint. (Index register set to select
Endpoints 1 - 4 only)
CONFIGDATA
Returns details of core configuration (Index register set to select Endpoint 0)
FIFO0
TX and RX FIFO Register for Endpoint 0
FIFO1
TX and RX FIFO Register for Endpoint 1
FIFO2
TX and RX FIFO Register for Endpoint 2
FIFO3
TX and RX FIFO Register for Endpoint 3
FIFO4
TX and RX FIFO Register for Endpoint 4
DEVCTL
Device Control Register
TXFIFOSZ
TX Endpoint FIFO Size (Index register set to select Endpoints 0 - 4 only)
RXFIFOSZ
RX Endpoint FIFO Size (Index register set to select Endpoints 0 - 4 only)
TXFIFOADDR
TX Endpoint FIFO Address (Index register set to select Endpoints 0 - 4 only)
RXFIFOADDR
RX Endpoint FIFO Address (Index register set to select Endpoints 0 - 4 only)
Target Endpoint Control Registers (Valid Only in Host Mode) - EPTRG0
TXFUNCADDR
Address of the target function that has to be accessed through the associated TX
Endpoint
TXHUBADDR
Address of the hub that has to be accessed through the associated TX Endpoint.
This is used only when full-speed or low-speed device is connected via a USB2.0
high-speed hub.
TXHUBPORT
Port of the hub that has to be accessed through the associated TX Endpoint. This
is used only when full-speed or low-speed device is connected via a USB2.0
high-speed hub.
RXFUNCADDR
Address of the target function that has to be accessed through the associated RX
Endpoint
RXHUBADDR
Address of the hub that has to be accessed through the associated RX Endpoint.
This is used only when full-speed or low-speed device is connected via a USB2.0
high-speed hub.
RXHUBPORT
Port of the hub that has to be accessed through the associated RX Endpoint.
This is used only when full speed or low speed device is connected via a USB2.0
high speed hub
Target Endpoint Control Registers (Valid Only in Host Mode) - EPTRG1
TXFUNCADDR
Address of the target function that has to be accessed through the associated TX
Endpoint
TXHUBADDR
Address of the hub that has to be accessed through the associated TX Endpoint.
This is used only when full-speed or low-speed device is connected via a USB2.0
high-speed hub.
TXHUBPORT
Port of the hub that has to be accessed through the associated TX Endpoint. This
is used only when full-speed or low-speed device is connected via a USB2.0
high-speed hub.
Copyright © 2011, Texas Instruments Incorporated
Peripheral Information and Electrical Specifications 275
Submit Documentation Feedback
Product Folder Link(s): VCE6467T AVCE6467T